Hi Guys, I'm relatively new to this and I've been researching lately but can't figure out how to properly do this and I have a Cisco Catalyst 3650. I have other vlans but I only want to access/reach the 100 and 200 (below):1. vlan 100 [workstations]1...
Forum Posts
Hi All,when i tried configure Cisco ISR 4331 Router it hanged 2 twice and i restart it, after restart, Router Booting with image ISR Software (X86_64_LINUX_IOSD-UCMK9-M), Version 16.9.2, RELEASE SOFTWARE (fc1). Instead of ISR Software (X86_64_LINUX_I...
Can you help with this lab?Configure Sw1:• Enable DNCP Snooping for VLAN 10• Disable DHCP Option-82 data insertion• Enable DHCP Snooping MAC address verification• Enable trusted interfaces
Hi guys, i have a question for you. If it's possible of course. I have some problems setting BGP in ipv6 environment. I have this sample configurationRouter:1conf tipv6 unicast routingrouter bgp 1bgp router id 192.168.0.1neighbor 2::2 update-source l...
Resolved! Cisco Modeling Labs - CAT9300
Hello, I have been playing around with both CAT9300V models in CML. I am trying to create a L3 port and setup eigrp neighbor between an IOSv device. when I create the L3 port I see the port in an UP UP state but I can not ping across to the othe...
I'm trying to configure IPSEC on a new ISR C1111-4P but showing an error when I try to execute the command.crypto isakmp policy so either the syntax has changed with the new XE IOS or is a license problem? how I can tell? Here is the version output a...
hi how do you create stub router using packet tracer version 8.2.1I have tried this command but did not workR2(config-router)#eigrp stub^% Invalid input detected at '^' marker.
Hello Again, I ask the question.I did a lab configuration on the Cisco provided site, and there was no abnormality in the ping test between the hosts.However, if you perform a ping test on the leaf device, a time out occurs.Q. The figure above shows ...
Hi,I have designed a Carrier board based on cisco’s ESR6300 module and we are facing issues regarding LAN and WAN coming up time after IOS-XE boots up.After powering on the ESR6300 Carrier board and after IOS-XE is booted up we ran command show run...
Hello experts, I have a topology like below: Three routers R1, R2, R3 are running DMVPN phase 1. And I configure by static mapping, like below: I attach my eve-ng lab file, you can download and check it. HUB:interface Tunnel1no shutdownip address 10...
In my lab NAT Overload is not working when applied to the interface but it does work when I apply a NAT IP Pool. What configuration am I missing here?
On a IOS-XE v17.06.05 router, I uploaded the NBAR2 pack and pointed to it with command. ip nbar protocol-pack bootflash:pp-adv-cat8k-179.1a-46-65.0.0.pack But it shows inactivate...How would I be able to activate it to replace the default one? Is it ...
Hi there,I tried to upgrade ROMMON firmware from 16.9(1r) to 16.12(2r) on an ISR4331 this morning, but I got the error "Upgraded ROMMON image failed verification check". Is there any workaround to fix the issue? ThanksISR1#upgrade rom-monitor filena...
I am reading a bit about EIGRP in the ENCOR study guide, and I found that for a route to be considered a backup route, the Reported Distance received for that route must be less than the Feasible Distance calculated locally. This logic guarantees a l...
Resolved! ACI l3out ospf and static route
We have ospf set on a leaf 101 ( DC1) to legacy router at DC2 , we want to have static route for specific host to remote side , I see that is done from the existing ospf L3out --noide profile leaf 101 and add static route ,the static route will take...
