Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
sh ver | i IOS|(revision)Cisco IOS Software, 2801 Software (C2801-ADVIPSERVICESK9-M), Version 12.4(3g), RELEASE SOFTWARE (fc2)Cisco 2801 (revision 6.0) with 235520K/26624K bytes of memory.Hello,We've been seeing our WAN connection drop every 20 minut...
A client of ours has Cisco 1811's on each side of a Metro E link. I don't have access to them, but had the client dump some of the output. I'm seeing a tunnel interface setup on each router running GRE. The default route to each site points to the...
I am working with a customer who is experiencing voice quality issues when Exchange replication is enabled or large files are moved from one site to another.This customer has four sites all connected by 10Mbps fiber leased from a local service provid...
At one of my remote sites i am getting complaints of dropped calls, so i take a look at their router and notice the CRC errors are climbing on one of the serial interfaces at a steady rate. I assumed it was a faulty T1 controller, so i replaced it, b...
I am putting in a bid for a large wireless job and I've contacted both Siemens and Cisco. I haven't spoke to anyone at Cisco except some people in Asia but Siemens actually sent people to me for this job. I don't get it.Can someone please tell me w...
i have a cisco 805 router conected to a DCE device that does not transmit the dcd signal. i have issued the ignore-dcd command but it does not work (the status is up but the protocol is down). other routers series (like 1700) work fine after issuing ...
hello, on catalyst 3750 (EMI) how to set clock in a permanent way ? after a reboot clock comes back to March 1993 without saving the time and day settings in ROM. I have to "clock set" it every time. how to fix it? thanksAD
Hi at all I'm working with a ISR G2 39xx. We added two EtherSwitch SM-ES3G-24-P Modules (SM Module) one in Slot 1 and the other in Slot2I would like to interconnect this EterSwitch Service Module together over the Backplane. Is this possible? How ca...
I have been researching the procedure to replace the ATM Interface module in a Cisco 3660, but I am not finding much. Are there any steps I need to perform or any tips I need to keep in mind when replacing an ATM interface module? I have never replac...
Hello,In one of my remote office, we have a 1841 device (c1841-advipservicesk9-mz.124-19.bin) with a WIC-1ADSL=that is used for Internet browsing and access to our private network through an ipsec gre tunnel.As the internet browsing is consuming a lo...
Confused about static routing.Tried to configure a static route on a 2620 router but is indicates there is no such command.i used ip default-gateway.I thought that is supposed to be used, or can be used, when ip routing is not enabled.when is this us...
We have an X25 SVC point to point link with a partner. In this link, we use the X121 address of our partner but we don't have an X25 address in our side.Does anyone can tell me if it is possible to configure routers to send X25 paquets over IP w...
HiI have Cisco 2600 Router .show ip interface briefInterface IP-Address OK? Method Status ProtocolFastEthernet0/0 xx.xx.xx.250 YES DHCP up up FastEthernet0/1 172.16.0.2...
Hello,I have a question regarding configuring WCCP for WAAS. If I have a subinterface does the "ip wccp 62 redirect in" command need to be placed on the physical interface only, on the subinterface, or on both interfaces? Thanks.
I use pre-shared keys for authentication, and I have written an automated script for periodically updating (rotating) keys. However, sometimes the rotation fails and I get paged in the middle of the night. So I had an idea:crypto isakmp policy 1 encr...
