Routing

Hello Experts,We are experiecing serious issue with the EIGRP Protocol.We are running a LAST MILE Routing protocol as EIGRP between the PE - CE Router.The EIGRP resets every 60 / 120 seconds for all locations and in the DEBUG the message that i recei...

can i change ospf update metric using route map? note i have one ospf instance.the configuration:router ospf 1 log-adjacency-changes network 10.1.1.0 0.0.0.255 area 0 network 33.33.33.33 0.0.0.0 area 0 distribute-list route-map cisco inroute-map cisc...

Hi iam upgrading me clients software and he has asked for some versions which iam having problems with below - can you answer the below questions.12.1(8b)E15 ENTERPRISE W/VIP SHH 3DESI see the above has been deferred and 12.1(8b)E19 is advised - but ...

Topology:1841===DMPVN_Clound===3825(hub)The 1841 has two HWIC-1ADSL installed into each HWIC slot. 1841 running 12.22T advEnt. Config looks like this:interface Tunnel100 description DMVPN 1 ip vrf forwarding monsters ip address x.x.x.x 255.255.255.0 ...

Hey Guys.I have a 3 spokes right now and two hubs. The other day I rebooted one of the hubs and noticed that I had lost the tunnels to all of my spokes. I thought they would continue routing through the head end that was still up but that wasn't the ...

We have a network with a Catalyst 500 switch and a 871 Ethernet router. The router has been configured ,with SDM, a SDM default medium security firewall. We observe that there is continuous traffic between the router and the internet(DSL modem). I ...

Hello all,Attached is a diagram of our network. Currently we're fully-meshed with MPLS between sites (A, B, C, and D) and a link out to the Internet (ISP1). However were looking to add an additional internet connection (ISP2).We use BGP at each site ...

I am having difficulty with a configuration on an 1841 router. I am just trying to connect the 2 ethernet interfaces to different IP networks and route between them. When I apply the attached config I am able to ping devices on each network, from t...

Hi, I need to connect a HQ office to 3 branch offices over point-to-point T1's.I know I can use frame relay for this but what other way will work? Is it possible to have 3 routers talking to 1 router with 3 WIC-1DSU-T1 cards, each with its own P2P T...

interface Serial2/0 no ip address encapsulation frame-relay IETF clockrate 1008000 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 102 interface Serial2/1 201endRouter(config-if)#do sh run int ser2/1Building configuration...Curr...

Hi , I have IPSEC configured between local end -Cisco PIX 515E & Remote end device - Nortel VPN box . Users from Local end use VPN to access Remote end applciations. But I am facing issues like VPN disconnections ( 10 users out of 30) intermittent...

Please I have some Ques.1. Is it possible I see the content of a 'copy config tftp' with notepad or any other format.2.Is there any diff btw 'copy run start' and 'write'.

Hi Teamplease let me knoew the name of IOS image supporting ATTACHED COMMANDS.on L3 switch 6509 and 3745 router.The existing IOS in switch is:s72033-advipservicesk9_wan-mz.122-18.SXF14.bin"The existing IOS in 3745 router is: c3745-ik9o3s-mz.123-12b.b...

With the command "sh policy-map interface <interface-name> I've got a list of the matched packets and bytes of my configured QoS class maps and so on. How I can reset these counters to zero? A clear counters doesn't help.IOS is 12.4(13r)T at Cisco 28...