I enter what's shown below, yet upon router rebooting (power off/on) I'm taken to Router> prompt instead of R1 prompt ! What am I missing in saving a boot configuration to the router ? If I can't save my work, what's the point ? (host name is one ...
I HAVE ATTACHED THE FILE ROUTER 1 IS NOT SHOWING ROUTE OF AREA 76 (i.e ROUTE 89, ROUTE 109, ROUTE 119) Router1#sh ip route ospfO IA 192.168.24.0 [110/129] via 192.168.13.2, 01:49:24, GigabitEthernet0/1O IA 192.168.34.0 [110/65] via 192.168.13.2, 01:...
Hi All, Very general question....Observed multiple times and recently too (related to ping drop). Thought to ask in community, if there is any technical reason behind the same, Three Scenarios : 1) Source and Dest hosts are in same VLAN.While pinging...
Hello i have a ASR 9006 cisco with 220 volt power supply chassisI want that chassis of ASR 9006 with continuous feedi need from expert ASR 9000 halp me and give me : what's command that allow chassis of ASR 9006 with continuous feed !! i wait a rep...
I had taken two PC and one Router PC 1 IP - 192.168.40.2GATE 1 - 192.168.40.1PC 2 IP - 192.168.40.130GATE - 192.168.40.129When I am trying to link these using IOS interface ..I can able to link PC 1 with the Router but when I try to link the PC 2 wit...
Hi, I am trying to connect my AudioCodes router MP-264 to 2921. How can I achieve this? Below is my topology: And below is my 2921 config hostname R1 ! boot-start-marker boot-end-marker ! ! enable secret 4 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ! no aaa n...
Hi, I have a Cisco 1921 which has the following Port Forwarding setup. ip nat inside source list 100 interface GigabitEthernet0/0 overloadip nat inside source static tcp 10.15.1.2 3389 interface GigabitEthernet0/0 3389ip nat inside source static tcp ...
How can I disable the broadband license? Below is show lic sum output. Router#show lic sumSmart Licensing is ENABLEDRegistration:Status: UNREGISTEREDExport-Controlled Functionality: NOT ALLOWEDLicense Authorization:Status: EVAL MODEEvaluation Period ...
Hi All, Just came across a new small customer site and can't understand how is the traffic being distributed/load-balanced across two WAN links on two separate WAN routers here. The configuration doesn't seem to have any BGP metrics to influence this...
We are trying to block port 25 outbound for all workstations other than the Exchange server. Here is what we've done (192.168.77.40 is the server):access-list 100 permit tcp host 192.168.77.40 any eq smtp access-list 100 deny tcp 192.168.77.0 0.0.0....
Hi,I have a 1941W router with the embedded ap, purchased second-hand. The router part of it is working fine, but I can't access the embedded ap - there is a user and password set and I obviously don't know this.I have tried with the default that I ha...
Hey guys, Not sure if this is the correct place to post this.Need help with something. Hopefully I can explain this correctly. We have a Cisco IR809G that transmits traffic over vpn to a Cisco firewall.In the past this cellular router was only used a...
I have a customer who has a very nicely working setup with a Cisco 2951 running as an EZVPN client to a head end. Because the 2951 is EOL, the customer is being pushed to replace this with a currently supported product. In looking at the datasheet...
have seen this document but it is not showing clear statement can you please just update me with below details 1-Router throughput capability: ?????2-Maximum Bandwidth can support:??????
I have configure EPC on an ISR4331 (IOS-XE 16.09.05) router interface but the buffer contains no packets after starting the capture. I'm specifically interested in UDP traffic on Etherswitch interface (Gig0/1/0) - the module is a NIM-ES2-4There is de...
