Hello, I am struggling to find the minimum supported release of Cisco IOS XE and Cisco vManage if I want to use DIA with IPv6 addresses. Thank you for help. Jan
Forum Posts
Certainly:"What kind of configuration should the hub have to communicate with the FW in SD-WAN Service Chaining?I read somewhere that the network service must be layer 2 adjacent to the WAN edge device. What does that mean?
By default the BW is set to 100K on the tunnel interface and the monitoring tools are complaining about this. is there any way to override this? Tunnel2 is up, line protocol is upHardware is TunnelInterface is unnumbered. Using address of GigabitEthe...
Good Day,I'm upgrading my C1100 devices from 16.2.5 to 17.06.05 via vManage. After doing the upgrade step, onto the activation, some of the routers are showing just "17.06.05" and these are failing with error "Cannot copy ios and sdwan cli configurat...
I want to establish a centralized policy in SD-WAN to route traffic to a particular destination FQDN. I understand that in vManage, there are Custom Applications that allow me to define specific FQDNs or applications. However, when attempting to crea...
Hello, We have Cisco Meraki MX75 device configured in Meraki Dashboard but not seeing events or logs when we do a API requestcurl --location 'https://n219.meraki.com//api/v1/organizations/{orgId}/appliance/security/events?t1=2024-03-11T24%3A00%3A00Z&...
Hi team, I need to understand when we need adding Root CA to vBOND controller in Cisco PNP. Suppose, I use on-premise controllers and enterprise CA for controller authorization. In addition, I want vedge authorization to be done automatically (vmanag...
Over the last several weeks, we have attempted to spin up new cloud controllers. One issue that held us up was our virtual account not showing up for provisioning. Then we inadvertently selected a dedicated host instead of shared so then were request...
HI if show vlan on nexusVlan244 is up, line protocol is up, autostate enabledHardware is EtherSVI, address is 003a.7d96.6f55Description: RaMINInternet Address is 172.18.14.1/30MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,reliability 255/255, txload 2...
Hello, For testing purpose, i have created a overlay tunnel between site-5 to site-6. Though, i am getting a service vpn 10 route via OMP but unable to ping those prefix from site-6 Vedge devcie. Can i get a solution or suggestion if i missed somethi...
Hello, I would like to ask if it is possible to configure 802.1Q on a portchannel. I attached an image of the topology. I would like to use the Po1.100 interface as a service VPN and the Po1.200, Po1.300 interface as a transport VPN. The device is an...
I am using Cisco C8500L-8S4X with SDWAN-image version 17.6.5a in controller mode and recently saw a crash on the router with the output below. I had gone through the datasheet and bug lists unfortunately I did not find any related bug that mentioned ...
Resolved! C8000v Device template issues
Hello, I am trying push an SD-WAN device template to a C8000v device. I keep getting the same error mentioned below. I successfully sent device templates to several vEdge devices on my network. Its just a basic config with VPN 0 and the transport int...
I'm looking to deploy SD-AVC in a closed environment without Internet access. This is to feed data into LiveNX for application performance statistics.Will SD-AVC operate without its cloud connector? All Cisco's documentation on the feature starts wit...
Hi community, are there any plans to povide NETCONF northbound API for the vManage? For now only custom rest api is available. Since vManage tech stack is based on NSO/confd it would be very nice to have NETCONF API for CFS side of vManage service to...
