Hi, I want to limit the number of BFD sessions a router tries to form, because all branch routers are starting to show up as partial connectivity in the Dashboard after deployment, even though from a design point of view, everything is fine.We're run...
Forum Posts
Hello, I have an SDWAN deployment with C1111 and ISR4331 as cEdge routers.There is no WAN connectivity and the reason is that there are no BFD sessions.Screenshots attached. On VPN0, it is configured allow service all, BFD feature template is attache...
Hello!I have an issue with vEdge installed in HQ on a Server, I have 2 ISR4331 in 2 Branches and one vEdge in HQ every time after Restarting when trying to ping to the vEdge IP (interface under VPN0) I Can't ping it, and when trying to ping from vEd...
i have getting below error while am deploying template to CSR 1000V and also similar errors in Vedge Failed to process device request. Error response : rpc-reply error: <rpc-reply xmlns="urn:ietf:params:xml:ns:netconf:base:1.0" xmlns:nc="urn:ietf:par...
I have 2 cEdges at a site..but only one of them will be connected to transport.So I could put the other cEdge in a tloc extension mode.(Even though it has no real vpn 0 transport) But my question is since the 2nd one wont have a transport itself what...
Resolved! vManage in Active/Standby mode delay
I have very small deployment 100 edges worldwide.I was looking at clutering however it seems to be designed for much larger deployments. I see there is a 4 ms latency requirement between vmange in clustering.So I am thinking of an east coast/west co...
Hi Team, pls help me to understand if we can perform link failover on vedges basis uplink utilisation threshold i.e. if MPLS link is being 80% utilised then traffic should be redirected onto IPSEC tunnel irrespective of latency, jitter and packet los...
Hi All, I have 2 vmanage clusters join in DR, each cluster consists of 3 vmanage, when viewed on the menu "Cluster Management" active-cluster looks normal but on standby-cluster an error message appears "Failed to list vManage Cluster".I Have restart...
Dears,I couldn't generate the CSR for vEdge from vManage interface. the 3dot tab doesn't exist.Please find attached the image.
Hi All, I am curious about explaination of LD/RD on BFD, Could someone explain it? Any suggestion will be very appreciated, Thank you!
Resolved! ENCS NFVIS deploy Centos fails
Hello, I'm facing the following Error while deploying a simple Centos VM on ENCS with NFVIS Gui: VIM Error Code for Unable to create resource in VIM, status code: 500: 500, VIM Response: {"uid":"ae4369cc-7725-4923-bf2d-f52c14e35723","description"...
Hi All , How can I test ZTP provisioning with vEdge cloud ? If you have any procedure or reference links , please share me .
Dears,I have an issue with vEdge cloud and vBond control connection.I have vManage, vBond and vSmart with version 19.2. I added two cisco ISR routers successfully and attached templates to them but when I try to add vEdge cloud, I face an issue which...
Resolved! Mgmt-intf vrf
I am trying to deploy brand new ISR 4331 routers with 16.9r and 16.10 code on them. My vManage template is very basic, just VPN 0 configuration, hostname, etc. When I try to push templates, it gives me a weird error message as per below. When I previ...
*Aug 19 13:20:51.217: %SYS-5-CONFIG_P: Configured programmatically by process iosp_vty_100001_dmiauthd_fd_176 from console as NETCONF on vty63*Aug 19 13:20:52.408: ENDPOINT TRACKER: Tracker get next hop not found for interface: GigabitEthernet0/0/1, ...
Recognize Your Peers
