Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Hi,on my c2960s-24-TS-L switch I have configured aaa, ssh and a user with privilege 15. When I open a ssh connection to the switch and login as the privileged user, I am not in the enable mode. On my 2960G switches it still functioning.Best regards,H...

hkupper by Level 1
  • 792 Views
  • 5 replies
  • 0 Helpful votes

     Experts ,Why answer is B ? Why route chosen is not  R6, R3, R2, R4, R1 when it has least cost ?Referring to the OSPF link metrics in the exhibit, which path will traffic from R6 take to reach R1?A. R6, R3, R2, R4, R1B. R6, R3, R2, R1C. R6, R5, R...

ranjeetba by Level 1
  • 977 Views
  • 3 replies
  • 0 Helpful votes

HiIf i connect a switch with better bpdu to a rootguard enabled switch port, the switchport will go root inconsistent state. and after a while when the new swicth ceased sending superior bpdus the rootguard enabled port will start forwarding.I need t...

           Hi  all,I have one issue with IP Communication not happening in the same Vlan,We have one Subnet 157.227.104.0 255.255.254.0We have server has two Lans One Lan is Configured with 157.227.104.xOther Lan is configured with 157.227.105.x  sti...

I just received my first shipment of 2960X's and am noticing the stack ring speed isn't showing what I would expect.  I have (6) WS-C2960X-48LPD-L in a stack.  There are no 2960S' in the stack where it would get downgraded.  Here is the output from a...

m.yost by Level 1
  • 6384 Views
  • 3 replies
  • 0 Helpful votes

Hello !When you have a vlan with multicast senders, how to have a router interface on this vlan to forward the multicast trafic, and without unicast routing.Before, with IP of senders in 10.1.23/0/24 , on a (old) 6500, this config works fine:interfac...

Hi,I have a custumer that they have a Linux firewall with iptables and like to migrate it to asa5505.The problem is a no tipical Dnat that it running in prerouting.This Dnat change the detination ip according the net from and port at the packages.Thi...

HIi need help i got a wireless router ( netgear) conected to internet (PPPOE) and a cisco AP1242AG. i want to conectr AP-to router wireless and extend the range of wireless network and it if is posible give net to ather pc on ethernet port aon ap.can...

wildserb1 by Level 1
  • 373 Views
  • 2 replies
  • 0 Helpful votes

I have just installed a new C2960-24PC-L switch and i have noticed a few of the ports keep changing their states.  *Mar 2 03:49:13.727: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/17, changed state to down*Mar 2 03:49:14.733: %LINK-...

CISCOBERG by Level 1
  • 1002 Views
  • 2 replies
  • 0 Helpful votes

Hi all,I have just update C1841 whith 2 ios diffrente (c1841-advipservicesk9-mz.124-25e.bin and c1841-advsecurityk9-mz.150-1.M3.bin) so the router can't boot. when I return back to the old ios (c1841-spservicesk9-mz.124-15.T10.bin) it boot successful...

My Name is Shameem Masthan, i woul like to get support and sugestion from you about to install my switches with recomanded Configuration. please find below the details what i am going to implement in my network. your quick response is really appricia...

Review Cisco Networking for a $25 gift card