Switching

Resolved! Cisco 861 Router - Slow Internet performance

Hi,I have a new 861 router which I have connected to my home broadband cable modem. Got it all working okay and I have access to the Internet but its not as fast as it is if I connect my laptop to the modem. My Internet is 60mb (was 100 but I downgra...

LAN Per-User Rate Limiting Solution

Hi All,We have a guest wireless setup but I need to rate limit the users so no one hogs all the bandwidth. The WLC is connected into a 3750 which is doing all the routing between the vlans. I know I cannot shape the traffic on the 3750 but can someon...

cisco 887w wireless

hi,could anyone please post configuration for wireless on the cisco 887w? i would like wireless and wired users on the same vlan if possible i am trying to bring the radio up but it says reset and down and cant get it to bring it up ( i have done vla...

Resolved! question in BGP route map ?

hi ,im using bgp protocol , and here is my config on my production network , "" i hided the ips with xx for privacy""%%%%%%%%%%%%%%%%%%%%%%%%%%router bgp xx99xx no synchronization bgp log-neighbor-changes network xx.xx.64.0 mask 255.255.254.0 network...

Resolved! i put an ipaddress on router , but why it gives my locally connected in routing table ??

hi ,i put the command on my router # ip address 10.160.150.3 255.255.255.0when i type #show ip route 10.0.0.0/8 is variably subnetted, 2 subnets, 2 masksC 10.160.150.0/24 is directly connected, GigabitEthernet1/1L 10.160.150.3/32...

undersized errors on 3560G

Hi All,I'm having weird problems with both of our 3560G switches. When I take a look at the port statistics via CNA I see a lot of underzised errors on trunk ports.When I take a look at the CLI via sh interfaces counters errrors I don't see any under...

dhcp snooping scenario

Hi everybodyh1-----sw1-------sw2-----dhcp serverWe configure dhcp snooping on sw1 and sw2. Sw2 is configured to trust to dhcp relay information i.e option 82. We want sw2 to remove option 82 before sending the message to dhcp server. Can we do that ...

Can't ping windows servers in different VLANs through SG 200-50 switch

Hello,Last week I installed a new router (2911) in my network.We had to create two different VLANs for the new setup to work as wanted.I have a Windows 2008 R2 which is a Domain Controller for Active Directory on the ip address 192.168.0.195.That ser...

Resolved! voice vlan and dot1p

Hi everybody.I am sorry I am still little confused about voice vlan.ip phone1-----sw1---trunk-----sw2----ipphone21) we configure switchport voice vlan 2 on both switches sw1 and sw2.Let say ip phone1 sends a frame to ip phone2.ip phone adds the dot1...

Resolved! IOS upgradation for 4506

Hi,I have 4506e core switch to which 10 other 2960 switches are connected.I want to upgrade thier IOS. how can upgrade it, can I upgrade it one by one or all at a time?Is there any tool to perform this task?

Resolved! VACL scenario

Hi everybody.How is everyone doing?h1----------sw1-----trunk-----sw2----h2h1----199.199.199.1/24h2----199.199.199.2/24Both h1 and h2 are same vlan2.We want to stop h1from reaching h2 using vacl.We configure sw1 as:Sw1(config)# ip access-list extende...

Resolved! How to allow communications between network segments

I have a WAN router that's on 172.x.x.x segment, and another WAN router that's on a 147.x.x.x segments.How can I make them communicate, I would like to interconnect both segments to talk to each other.We are using a Cisco 2800 on both segments. ...

Setup LAG between Cisco SGE and Catalyst Switch

HI there,I'm trying to setup a LAG between a cisco sge2010 and a catalyst 3750. However when I set it up the switches are throwing up a huge amount of "flapping" errors.I've attached a doc that explains how this was setup. Can anyone explain what I'v...

Redistribute BGP Routes to OSPF

Hi,BGP newbie here. I was messing around with a few different configs on GNS3 and Packet tracer. The lab I was trying to build was 2 seperate locations running OSPF, with a router in the middle running a basic BGP configuration. Everything is work...