Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

 
Labels

Forum Posts

Hi,I tested obtain IP through 2950 and 2960 model. My PC connected to interface g0/19 which configured be mirror port.My configured on both models are identicalmonitor session 1 source interface g0/11monitor session 1 destination interface g0/19 ingr...

Rojer-bkk by Beginner
  • 967 Views
  • 6 replies
  • 0 Helpful votes

Hi every body.My book says  the value of config-register is stored in nvram.  Let say our config register value is( boot field) is 1, which means  load the ios from first ios file in flash.  Let say we power on our router( cold start) ,following sequ...

sarahr202 by Contributor
  • 1276 Views
  • 1 replies
  • 0 Helpful votes

i have Cisco 6509-E series sup 720 with ios version. I want upgrade same sup 720 in different 6506 (without E)  and put in 6509-E. Is it possible?

cssam by Beginner
  • 764 Views
  • 1 replies
  • 0 Helpful votes

Hi Team,               I was configuring 3750 stack, I am supposed to run bgp on it. after making a VLAN , i got an err messege as below.PSECURE: Assert failure: 0: ../switch/psecure/psecure_ifc.c: 291: psecure_get_vlanid-Traceback= 7BCADC 7C149C 7BA...

Hello All- Upgrading IOS image on our 6513s from 12.2(18)SXF7 to SXI4a or SXI5. Memory requirements are512MB DRAM and 512 MB Flash. Appears we have 512/64:System image file is "disk0:s72033-advipservicesk9_wan-mz.122-18.SXF7.bin"cisco Catalyst 6000 (...

We have a Cisco 7613 router and we are using it to aggregate the customer on through ethernet and E1s. The CPU utilization reached 84 % since the last couple of weeks. Below is the " show proc cpu sorted" command.CPU utilization for five seconds: 80%...

Hi,My network consists of 2 sites (A & B). Both sites each have 2 units of Cisco 6506 switches. Between Core1 & Core 2 both  are running HSRP.All the active gateways are at Core 1 & standby at Core 2. Both sites are connected via DWDM which physicall...

ganeshp by Beginner
  • 525 Views
  • 1 replies
  • 0 Helpful votes

Hello All.  I may be trying to fix something that isn't broke, but here goes :I have 2 access switches, both 6500's - Sup 720's, connected by gig fiber, trunked.  Switch A is our LAN switch, while Switch B is in our server room.  A is connected to th...

If a switch running VTP v2 boots with VTP server mode in the vlan.dat and VTP transparent mode in the startup-config and in the startup-config are configured some extended-range VLANs, is it possible to have a VTP server with extended-range VLANs con...

I have a customer considering the ramifications of not covering their C6509 chassis (243 in the core) and do hot spare scenario.  What are the IOS entitlements for C6509 that are not covered by a maintenance contract?  I would also like to do a compa...

breblack by Beginner
  • 279 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Redundancy sso

Hello All,I have  following configuration on my swtich but i am unable to understande notification-timer 240000 command. Can you please help me to know what deos this do?redundancy notification-timer 240000 main-cpu  auto-sync startup-config mode sso...