Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Resolved! eigrp trouble
Hey I connected two 3560 cisco-switches through their gig0/1 port. Wanted to use eigrp to make the routing connection work.But when I do a 'show ip route eigrp' command , nothing comes up. In 'show ip route' I only see C's and no D's. I will displ...
Resolved! Router Dropping Pings
Working with 2 Networks: NW1 using static IP NW2 using DHCP. Pings are successful across LANs but drop between the routers. The routers can ping each other individually, but their networks are inaccessible. May I please have assistance? pa...
I am learning to multicast for ipv4 and have a few questions.Okay, I understand that with multicast, every member in the group is aware of a mac address that will be recognized as a multicast frame.When it comes to a switch, I know that a broadcast u...
Resolved! ACL block telnet
Hi Experts, doing a lab for ACL to block telnet for PC2 (10.0.0.2 ) even and on another side, all systems should use telnet.I have access-list 100 with the below config. permit tcp anypermit ip anydeny tcp host 10.0.0.2 any eq telnet telnet not block...
Resolved! Stackwise Virtual C9300
⁶Hi, Did mistake by configuring virtual stackwise in C9300 switch . I know it doesnt support VSS. Now both switch keeps on restarting. Error: waiting for 120 seconds for other switches to boot#######Jun 4 15:10:59.082: %PMAN-3-PROCHOLDDOWN: F0/0:...
Resolved! Voice and Data VLAN
Hi, how can I allow data and voice VLAN on the port?on SG300 Switch. Sumy,
I have tried to follow the "Recovering Catalyst Fixed Configuration Switches from a Corrupted or Missing Image" tutorial shown belowhttps://www.cisco.com/c/en/us/support/docs/switches/catalyst-2950-series-switches/41845-192.html however it still does...
in this topology , bgp neighbor is not done between R1 & R3 & Both Router are not even configured by static route ,Will R1 be reachable with R3 in this case
Hi, We have facing the issue about IP hsrp active intermittent, but the IP hsrp standby is running well. Based on best practices on our topology environment is all of connection redundancy. Is there any problem with spanning-tree?
We have our switches and routers configured with aaa login via a RADIUS server on NPS. When we login to the devices using ssh and telnet, we can login using radius credentials and everything works. The user is automatically taken into enable mode. ...
Hi all,i just nned to know is is there any way to prevent network from MACflap.The best way will be when switch will disable the interface where the macflap was detected.I need to set this security feature on 2960s.Thanx a lotBRDave
what is diff betwen "sh ip route bgp & sh ip bgp" command
Hi,I'm have a SPAN session on a 6509E which has a number of VLAN's SPAN'd to two 10Gbps interfaces. This is working fine, but I would also like to include the 802.1Q VLAN tags on the captured packets so I can tell which VLAN each packet originated on...
Resolved! C3650CX - %ILET-1-AUTHENTICATION_FAIL
I have a Cisco Catalyst 3650-CX that was just updated to v15.2(7)E4 from v15.2(7)E2. Post reboot, I'm receiving the following log message every 5 minutes:%ILET-1-AUTHENTICATION_FAIL: This Switch may not have been manufactured by Cisco or with Cisco's...
Hi,I want to upgrade IOS firmware upgrade of the following cisco switches WS-C3650-24PD& WS-C3650-48PD currently version 15.2 is available, can anyone provide me link to download latest IOS firmware upgrade link to download and upgrade these switche...
