Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Hipls help me by forwarding the links relating(cisco notes)V-lan and Access-list.Thanking you
Between: 4-Port 10/100 Fast Ethernet Switch WIC4-Port 10/100 Fast Ethernet Switch WIC (spare)Best regards
hi guys plz help me in this,i have 3 routers connected to each other like this O------------O----------OR1 ISP R2i m using a tunnel over ipsec to allow routing via ospf between R1 and R2 everything goes fine, but when the tunnel goes...
Resolved! Managment VLAN on a Switch
Hi,I'm trying to get a Management Vlan running which isnt VLAN1 due to the secruity issues and best practise.I have programmed switch as shows:!ip subnet-zero!interface FastEthernet0/1 switchport access vlan 10!....!interface FastEthernet0/24 switchp...
hello folks i am new to cisco i have 14 cisco routers some 2500,2600,3600,switches,1900,2900,3500,i have read the setup for telnetting with the 2511 can telnet to most but not to all,i am using both asyn lines any reason why i cant connect to all the...
Hi guysI have a cisco 4503 core switch and about 5 edge switches 3560 , one for each floor in my office. I have configured a dhcp server with the respective number of scopes as number of vlans which is 6 in this case. Ive set the IP helper address an...
I have 2 Cisco 2950G-12-EI, S1&S2 connected with two uplink cable as the other one is redundant. S1/P11 connected to S2/P11S1/P12 connected to S2/P12(Blocking State)How I can enable the S2/P12 to forward state, so that if I have a host connected in S...
Resolved! 2511 reverse telnet
Hi again . now I was able to get from comm-server 2511 to 2610 when I canfigured the loopback0.. now I wan to getback to 2511 com-serv its says on the doc that I need to do Ctrl+shift 6, twice// I did but I am still on the R1 PROMTdo I need to config...
Need the following objectives:Need 1 WAP Cisco 1130 to have 2 SSID's and each one it's own separate VLAN. - Vlan 18 is going to for employess - Vlan 19 is going to be "public" it will only have access to InternetI have 1 vlan for internet which i...
Hi Does anyone have inroads to cisco to check if they have plans on releasing a new Supervisor Engine for their 4500 series. example support for more routes would be a great start!Tyrone
I have a 6513 as server in VTP domain, I want to disallow few vlans on the trunk ports to different switches. I am unable to do so I am running the command clear trunk 8/2 51Removing Vlan(s) 51 from allowed list.Port 8/3 allowed vlans modified to 1...
Is it possible if I have a redundant link between 2 Cisco 2950G-12 and I will not encounter any timeout if the one uplink fail. S1 and S2 has host connected on it. HostA(S1) and HostB(S2), if I want to ping from HostA to HostB.
HiI have a Catalyst 3550 Switch with IOS version 12.2(25)SEBCan anyone please give me a complete on how to do a QOS for VOICE traffic on several ports.E.G.I have two voice gateways connected to two different ports on 3550 and want to prioritize their...
The following output shows that the catalyst 6500 have snooped the multicast address 0100.5e00.0190 on port gi1/24 and gi2/24.Question: How do I disable snooping on these L2 interfaces.SD00#sh mac-address-table multicast igmp-snooping vlan mac addr...
I'm studying for BCMSN and have read in several places this statement: "Devices in a campus network's core layer or backbone should be optimized for high-performance Layer 2 or Layer 3 switching."Why would you go from layer 3 in the distro layer back...
