I am seeing the TRTL throttle count increasing under a Gig interface when I do a 'show int gi7/1 summary' command on a 6509.It is mainly multicast traffic from several sources to a single server that is going across the port The port is set as a swit...
Hi all,Our sys admin is using a Sw delivery pkg; the pkg works by sending wake on lan packets using broadcast before delivering the pkgs; naturally, these broadcast pkts are not reaching other vlans. What can i do to make them do this?thank you.
Hi, I have 3550 Switch.Model number: WS-C3550-24-SMIDoes this support PoE. (Don't have access to router.)How to find if my switch support PoE.Please Help.Cisco Internetwork Operating System SoftwareIOS (tm) C3550 Software (C3550-I9Q3L2-M), Version 12...
I've got what appears to be an arp problem on a Cisco 2620, IOS 12.2(15)T5 on our network. It is plugged into a Catalyst 2924XL that is setup for 2 VLANs, with another router that is being used for Nat translation and bandwidth control based off of ...
I have a catalyst 4000 switch that I inherited. It has never been used,and I am required to configure it so that we can use it for VoIP. I cant even find the manuals that came with it, and I have to connect into it so i can configure it. Can anyone h...
I implemented VLAN in my network and make the 5 switches to have the default vlan 1. But i discover from time to time that when i launch the Cisco Network Assistant, it shows "Switch Failure, can not connect and Switch Unreachable". Ping still goes t...
Hi all, we are having issues with our aironet access points, for some reason if there is no activity for a while we cannot connect back to the ap, we have to use a keepalive program so we can always see them, does anyone know what this could be ?carl
Is there an way to monitor the bandwidth per port on a 4506?? I know that CNA lets you monitor the overall bandwidth and you can do link bandwidth monitoring but is there a way to track it by IP or MAC address back to the source??
We have (2) 72xx routers with 3 internet connections. We are running BGP and OSPF. We currently get our gateway of last resort from only one provider. We had problems with that provider on Monday, and we lost the gateway of last resort. We are di...
we have a router cisco 3825.the router has 256 mb of memory, but it is not using all of it because of dead process which is called "usb_startup" this dead process takes something like 60mb of the router memory. the reload command doesnt solve the pro...
I have a gig port on a 7206 connected to carrier's fiber switch. we are seeing large amounts of output drops on that port. carrier says they do not see any drops on their equipment. it is connected at 100/full. Total output drops: 242179any help w...
WHat is the capacity of the disk in the SSM-20 module?Thanks!
Hi, As far as I know, FIB is the same info from the routing table but should be "reformated into a ordered list with the most specific route first". Having a look to several FIBs, I ve never seen most specific route first. Following example, 192.168....
Hi folks,just a question: with two 6704 4x10Ge modules could I create a 20 Gbit EtherChannel with two links on different modules?I've tried, but one remains always in err-disable, and I don't understand why.Any advice will be appreciatedRegardsAndrea
HiI am a little bit confused about HSRP.I know why it is used for.But i just want to confrim the below query.i have 2 3560's configured HSRP between them.As long as the link between them is trunk everything is fine,when i changed the link to layer 3 ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 04-23-2025 06:26 AM | ||
| 04-23-2025 06:18 AM | ||
| 04-19-2025 09:40 AM | ||
| 04-15-2025 04:52 AM | ||
| 04-11-2025 03:44 AM |
| User | Count |
|---|---|
| 7 | |
| 6 | |
| 6 | |
| 4 | |
| 3 |
