Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
I have DLSWitchA = Cat 3550. ALSwitchA1 and ALSwitchA2 are Cat 2912 connected via crossover cable to Cat 3550 ports fa0/1 and fa0/2 respectively.Then I configured the port on the cat 3550 as int fa0/1 switchport encap dot1q switchport trunk Then I g...
Hi I have two cisco 2500 routers and am connecting them back to back with a DTE-DCE cable. Can someone explain how I can configure the speed of this line? I set my clock rate to 64000 so does that mean the line speed is 64kbits?Thanks
We have a rps connected to a 2950-24 switch, the power plug was accidentally knocked out of the switch and the rps-300 took over supplying power,when we plugged the switch back in the rps won't release supplying power. If we put the rps in standby mo...
Hi,We are trying to set up command authoristaion.On VTY evrythings working out but it is not authorising anything on console.In debugging aaa authorisation it only tells me :Jun 17 01:45:50: AAA/AUTHOR: authenticated console user is permittedAnyone a...
Alright, I will be upgrading my production 6509 SUP1A's to SUP2's. What is the best possible method to reduce downtime ?- Is there any scenario where I can eliminate downtime and ensure that all servers switching on modules 6,7,8 remain connected. Th...
I have a catalyst 2950G at plant with two pannels (IP Managed by a Server placed at my CPD) connected and from some moment ahead one of them started to fail. We used a sniffer and the traffic sent for both is the same and to certify created an ACL (j...
Alright, I have a MSFC2 (via switch console) that continues to reboot and does not allow access. Just keeps cycling thru uncompressing the boot image.Am I dealing with a corrupt image ? If so what steps should I take to resolve this ?Thanks in advanc...
I have a lab with 7 routers running PIM in sparse-dense mode with Auto-RP. Everything seems to work, but on some routers pinging a multicast group address produces more than one response:R1#ping 239.0.0.1 rep 4Type escape sequence to abort.Sending 4,...
Resolved! Diagnostics that can be run on 6509
I have a 6509 with the fan light set to RED and 2 fans are not spinning anymore. I would like to know what command can I run that would show me this failure and anything related to the power supplies.
I have an old 7206 router. I need to have it pass cipso packets. however whenever the user tries to send them across the router it generates an icmp error. I know it recognizes the cipso packet as it shows up in "show ip traffic" tried various ip...
is it possible to create your own IOS to incorporate dynamic content such as PHP or perl. Also how would I use one of the serial ports to send & receive data.
We r configuring the new summertime on the CAToSes and the summertime setting is disable by the default. Do we need to enable it when we r configuring the summertime command or leave it disable?thanks
Hello all;I have two routers connected each with two ethernet cables to a layer 2 switch. see the diagram. I want to get each router to know about each other lan using static routes only i dont want to use dynmaic routes meanwhile preserving the redu...
Hi all, can anyone tell me if we need to use both when setting up a voice network, i believe cos is on switch and qos it on router? can we just use cos and it easy to configure
Hi all. (waiting for TAC support to register me)I'm trying to find information on setting up a Dynamic NAT for my 1841 using the SDM. I know how to do the static NATs and they seem to work fine. However, our Japan office would like Dynamic NAT. Where...
