Hi Techies, We have 2 cisco 9300 switch installed in our infra, 1 switch is use for Core activity and another is Access Switch, the routings happed on the core switch... on the Core SW have different VLANs example Vlan 50 (Subnet - 192.168.10.0/24) ...
Forum Posts
I've got a VSS pair of 6880-Xs in a VSS pair running 15.2(1)SY6 as the network core switch connecting to various IDFs with a pair of fiber in a portchannel. We also have some monitoring software that pings the IDF switches periodically go see if they...
If there are 2 switches stacked uplinks given to each 2 switches with 2 ports each, say eg port 47 & 48.Port 47 & 48 are created LACP for each switch Then what is the use of stacking here for redundancy?I am newbie. Please explain.
Hello everyone i need to monitor something like 200 cisco switches (some 2960-x) and i want to know what SNMP solution would you use ? i think of Cacti or Zabbix what do you think about it ? thanks in advance
I have a 3750 switch that currently will only display this error:%% Low on memory; try again laterThe only warning/error that is on our logging server previous to this is a traceback error. Thier is no history of this on this stack, and if it was so ...
i experts, I'm getting this repeated notification daily since 3 days and now I received a complains that the IP phones keep getting restarted in the switch location offices. logs from core switch : Sep 26 06:34:26.664: %SFF8472-5-THRESHOLD_VIOLATION...
Hi,I have a quick question regarding the Stackwise configuration for 4 Catalyst 9300 switches. In terms of connecting them, which scenario would be correct:Connect switch 1 stack port 2 to switch 4 stack port 1 ORConnect switch 1 stack port 1 to swit...
I have a question about HSRP and ACL configuration on Cisco 4506 and 4506E switches.Initially, without HSRP enabled, I configured the following ACL on the VLAN 55 interface:Extended IP access list vlan5510 permit ip any 192.168.104.32 0.0.0.1520 per...
I know this has been discussed, but my situation may be more unique. We were having issues with a 24 port POE 3850 not being able to power all necessary cameras (13 I believe). It has two 710w power supplies which is more than enough for this applica...
cisco nexus 9000 c93180yc-ex SNMP configuration for whatsup gold 24.0 build 2096 We are getting credentials error after configuring the SNMP for Whatsup gold.
Resolved! Switch c2950 iso copy issue to TFTP
MT-Test-01#copy flash1: tftpSource filename []? c2960x-universalk9-mz.150-2.EX5Address or name of remote host []? 192.1.2.200Destination filename [c2960x-universalk9-mz.150-2.EX5]?%Error reading flash:c2960x-universalk9-mz.150-2.EX5 (Is a directory) ...
I am curious about configuring bandwidth restrictions for specific VLANs through a switch. For example, restricting a guest Wi-Fi VLAN to 10 Mbps. While this can typically be done via a wireless controller, the customer requires this to be configured...
Hi everyone , i am quite new . I have been stuck up from quite few days . i have to implement a solution for the below requirement . 1) i have 15 devices with same ip address ( ip address is hard coded inside and can not e changed ).2) each device...
Greetings! Let me start by saying I am NOT a network engineer, so I am just now learning how to configure VLANs on switches.What I want to do is to set up two separate VLANs on a SG-200 switch that are totally isolated from each other, replacing two...
Resolved! switch: CCCCCCCCCCxmodem:: I/O error
hello I goofed and uploaded a new image to my Cisco 3750.I deleted the prior image and set the boot flash statement and then used the command boot system flash: old image/new image This caused me to enter into switch: mode I have tried various recove...
