Activity in Technology and Support
How to bulk change Administrator password in CUCM cli?
Hello, I am looking for a solution to bulk update the CLI password of 50 CUCMs that all use the same password. Logging into each CLI one by one and repeating the same steps every time is very time-consuming.I also don’t feel like reinventing the whee...
Can we run eBGP over IPN network in ACI multipod environment ?
We are planning to migrate from N7k to ACI Multipod .In our existing environment, we have a L2 extension between the two DCs to create a eBGP peering between our firewall in DC1 and DC2.Can we do the same setup in ACI Multipod over IPN ? if we extend...
Resolved! Phones suddenly did not register and gets rejected
Hello,I'm having issues with the phones in the same cluster. It gets stuck to registering and gets rejected after the phone reboots.We successfully upgraded our CUCM from 11.5 to 12.5 a week ago.CUCM cluster filled up the active partition to 98% afte...
Group Policies dropping from clients randomly on firmware MX 19.2.8
With the recent firmware upgrade on all our MX security appliances to MX 19.2.8 we are encountering our users that are (VPN Client) & (Wired Client) dropping off their assigned group policies in an everyday basis. What would cause this issue and w...
Resolved! - D-Channel Blocked -
My ISP says the router is 'blocking out the D Channel'I am using an MGCP gateway backhauling the ISDN to Call Manager - I am seeing 'path code violations'yet when the telco puts a loop in the line, it tests clear.They insist is it the CSU (customer s...
Etherchannel to Etherchannel
I have a Catalyst 5509 and I am unable to ping from one etherchannel connection to another etherchannel connection. I have 2 linux boxes connected to the switch via etherchannel. I can ping the switch from each linux box. I can ping each linux box...
CSCwf97711 - On vEdge 1000 getting reset after RTC reports PWRFAIL
We are getting the below error at vEdge-1000 WAN router however there was no power outage at site.RTC reports PWRFAIL @ 11:39 on 07/06, powered up again at 09:44 on 08/06What is the solution for this error. this is affecting the Guest wireless servic...
Problem during boot cisco catalyst 3650 switch
Hello everyoneI have a huge problem with an old switch catalyst 3650 48FS-E, I do the command factory-reset all, then the switch boots by itself and stuck on the mode of the first Image that upload although I do the command flash_init then the comman...
IOSvL nodes and disabled switchports
I've configured multiple OSPF labs, in CML, using the IOSvL node...disabling switchports on those nodes in each lab. (The labs have not been deleted.) When I configured an OSPFv3 lab (my third OSPF lab), initially, the two disabled switchports on two...
XDR Automation Rule targeting Detections
Automation Rules can target many things, but I would like to use detections as targets rather than incidents, as not all detections are raised to incidents. From the detection alone, there might be certain actions I would like to take. If detections ...
DUO v5
Hi,We recently updated workstations from v4 to v5 and before updates were applied, a user would receive a push on their cell phones but now DUO prompting for PIN #. Also, the authentication screen had a box to "remember me for 12 hours" and that box...
Re: Cisco 8851 phone keeps trying to register
I just deployed my CUCM 15 in production, and everything goes well until I connect the IP phones for testing. Unfortunately, I can't see the phones in CUCM, even though they are receiving IP addresses from DHCP as well as CUCM's own IP addresses (PUB...
Can ping a device from secondary L3 switch but not from Primary
rimary and Secondary L3 switchesCan ping devices connected to a L3 switch on a vehicle over Fluidmesh wireless IP addresses 10.3.6.11 and 10.3.6.12 from Secondary [standby] switch. This vlan 306 10.3.6.0/24 exists only on the vehicle. When attempti...
Resolved! The number of ASDM sessions has exceeded 5 on ASA5520 running 8.2(1)
I have an ASA 5520 running version 8.2(1) and I am having an issue with ASDM sessions.I can SSH into the ASA and have tried to clear the sessions but they do not clear as per below.largoGW# sh asdm session0 dguselnx1 dguselnx2 dguselnx3 dguselnx4 dgu...
BETA Alert! RadSec-Direct Open Roaming for Cloud-Managed APs
Seamless Wi-Fi connectivity just got better for Cisco customers using cloud-managed access points!We've fundamentally reengineered OpenRoaming — optimizing the three things that matter most: speed, scale, and control. The legacy proxy-based authentic...
| User | Helpful Count |
|---|---|
| 97 | |
| 82 | |
| 48 | |
| 48 | |
| 47 |
