Activity in Technology and Support
SDWAN - configuration push
when I pushed the configuration from manage, it has been pushed the OSPF configuration but rolled back to default with in 3 mins without any errors.please share your suggestions to troubleshoot. I am new to SDWAN
ASA to AWS IPSec tunnel - ASA is not initializing communication
I'm trying to initialize IPSec tunnel to AWS basing on AWS instructions and it looks that ASA is not even trying to initialize connection.When I turned on debugging, it looks that ASA is in receiver mode (I see connection attempts from old site), but...
Can Kandji MDM be integrated with ISE?
Hi,Is it possible to integrate Kandji MDM with Cisco ISE?I have been looking for guides but so far not found any.Our company uses Kandji MDM for the management of Apple devices and we want to integrate it with ISE to enforce NAC. I have just finished...
How can I get area A to talk to area B?
Hi there,I am using packet tracer and I have an issue with area A talking to area B or area B to area ACloud is configured to use modem4 to Ethernet6Server has DHCP on and can talk to router and other PC in area A but not area BArea A inside IP is: 1...
CUCM - PAM (Pluggable Authentication Modules) and SSHD (Secure Shell)
Hi, We have received alerts that PAM (Pluggable Authentication Modules) and SSHD (Secure Shell Daemon) are disagreeing on the maximum number of password retry attempts allowed for a user. From my research conducted the sshd_config file'MaxAuthTries"...
Smart Software On-Prem Console - upgrade to 9-202504 failure
Has anyone else attempted an upgrade from 9-202502 to 9-202504 yet? I've tried it 2 times so far - both fail at the final step (it seems the application doesn't complete its startup - at least according to the syslog). Thankfully rolling back to the ...
IP And MAC Address Issue
I am having issue with one of my desktops connected to my switch interface flipping between two MAC addresses (see the attached picture below for log). When I disconnect the desktop the IP and the MAC issues will not show in the log. I reimaged the ...
Need help setting up Cisco 561 headset to laptop
I was given a Cisco headset 561 with standard base as a gift since we work from home and want to be able to walk around and answer calls without staying by the desk. The headset was purchased from Ebay, and they sent it without any paperwork and inst...
Catalyst9000 IOSXE 17.12.5 Default values
I have a question about the following default values in Catalyst 9000 series version 17.12.5.・no thermal shutdown disableI have a concern that the temperature will rise and the power will be turned off when the FAN fails.・no ethernet reuse subInterfa...
FTD Rules
I'm learning the basics of FTD (FP1010) and doing some tests. Using FDM, I create an ACE Rule to block ICMP (any type, any network). It’s the first rule on top of other policies, setup as Block and log. I can see the rule being triggered if I try to ...
Mikrotik Replacement
Hi, I recently opened a case with GVE and they indicated that they ceased active support for Service Provider architectures in October 2024. I have a ISP currently requesting to replace the following, Replacement for MikroTik CCR1072-1G-8S+ -72-core...
Direct Attached Storage to Fabric Interconnect for iSCSI?
We have NetApp FCoE storage directly attached to our Fabric Interconnects which is the Cisco recommended method at least for smaller implementations based on port density. This reduces latency and reduces complexity as you don't need to perform zonin...
Easy VPN Nework Extension Mode
Folks, I have an old school question. I have a use case that I think can be well met by using the Easy VPN solution using "Network Extension Mode" as opposed to "Client Mode". Is this capability still supported on new ASA firewalls or IOSXE routers? ...
How to convert two routed interfaces between two pair 9k and pair 7k t
We have pairs of N7K and N9k connecting via eigrp (full mesh), each one of the pair connected to two mpls routers, each pair have routing table, I am looking to replace the routed interfaces between pairs of N7K and N9K with vPC, is that possiable ? ...
video calls not working (cisco ip phones 8865) in cisco ISR 4431
Dear Team,video calls are not working on cisco cme (cisco isr 4431). we are using cisco 8865 phones and registered in cisco 4331 Voice gateway.Please do the needful
| User | Helpful Count |
|---|---|
| 97 | |
| 66 | |
| 62 | |
| 60 | |
| 59 |
