Activity in Technology and Support
CVP 12.0(1) – DatafeedQueueThread accumulation after updateApp
Hi,We are observing a possible issue with DatafeedQueueThread accumulation in Cisco CVP 12.0(1).When updateApp is performed while the application has active calls, the old application configuration remains active for existing calls, while a new confi...
MPLS LDP Label Filtering - Multiple ACLs
Hello, everyoneThis is my topology with the following prefixes:My goal is the following:R3 should advertise only 3.3.3.3/32 and 33.33.33.33/32 to R2.R3 should advertise only 3.3.3.3/32 to R1-XRFor the first rule, I've defined this ACLR3(config)#do sh...
UCS-220M8- CIMC Screen-Keyboard not responding
Hi All, I've a Cisco UCS200M8 Server with firmware: 6.0 (2.260044)Server was previously connected to a FI 6454, During that time the server failed discovery due to firmware incompatibilty.After disconnecting the server from the FI, i'm now trying to ...
Cisco + Ubiquiti: Is It a Smart Combination?
Hello everyone,We're currently planning a network upgrade using Cisco as the core infrastructure while considering Ubiquiti for branch offices and wireless connectivity.For those who have experience with both platforms, how has this combination worke...
Custom UI buttons to control microphone groups ,camera layouts on EQ
Dear Cisco Community,I hope you are doing well.I am currently working on a Cisco Room Kit EQ deployment and would like to implement custom controls on the touch panel using UI Extensions and macros. I would appreciate your guidance and best practices...
VTP Mode Change from Server to Transparent VLANs Disappear
Hello All!I did some looking around the forums and found what I think might explain the behavior we ran across today, but I wanted to ask the experts to see if we are on the right track. Here is what we saw:We had a 3550 switch and a 3745 router. B...
Resolved! Stackwise virtual with meraki dashboard in Cloud configuration
Hey there,I am trying to create a stackwise virtual setup with 2 x C9500-24Y4C through the meraki dashboard.When i am connecting my 2 interfaces dedicated for the SVL and 1 interface for the DAD, STP kicks in and blocks the 3 ports on the 9500-2 then...
Cisco SD-WAN: cEdge not Showing Remote Device interface MAC Address
Hello everyone,On Cisco cEdge devices, I'm not able to see the MAC address of the directly connected remote device interface from the CLI, regardless of whether it's a Layer 2 or Layer 3 connection.Is this expected behavior in Cisco SD-WAN, or could ...
SSH Node Timeout on Long-Running Tasks
I'm running into a problem with the Unix/Linux Execute SSH Command node when the remote command takes longer than a few minutes to complete.Behavior observed:- The node establishes an SSH session to a remote host and executes a long-running command.-...
New IOS-XE 17.15.5 Update - LOTS of fixes and changes.
There is a lot here, read carefully if you use these switches!Important notesAfter upgrading to Cloud Management with IOS XE 17.15 it is not possible to downgrade to any CS firmware via Dashboard. In order to downgrade to CS a factory reset may be re...
ISE Posture update issue
Hello mates,I’ve seen this error while trying to do a posture update: “Feed cannot be generated or parsed”:We have it for two weeks now and we patched our deployment yesterday but the issue is still here. When I try a to update now, I see my proxy go...
BGP vpnv4 not able ping
We have an MPLS L3VPN connectivity issue affecting one specific remote site. Topologi is below.AGDM has MP-BGP VPNv4 sessions with both XINDI ASR920 and 4YOL ASR920. The VRF is VOIP. AGDM has ibgp with MSE2 (AS34170).AGDM successfully learns the VOIP...
CUBE to SIP-Provider across firewall with no ALG
I am trying to configure a SIP router across a NAT firewall with no ALG.I am trying to replicate in my lab before deploying in production.I am having a hard time getting it to work.The call flow is like this:CUCM > SIP-CUBE > NAT-Firewall > SIP-PROVI...
MPLS LDP Password Rollover
Hello, everyone.This is my topology:The timers for the TCP session are 20 for KA and 60 for the holdtime.Both of these routers share a password called CISCO8. I was told that the mpls ldp password rollover command specifies how long will the router w...
Official Public Source of Cisco YANG Models
I am currently building a structured API RAG system and need an authoritative public source of Cisco YANG models (IOS-XE / IOS-XR / NX-OS).I understand that some models are included in device images, but for automation and model-driven programmabilit...
| User | Helpful Count |
|---|---|
| 72 | |
| 65 | |
| 64 | |
| 46 | |
| 45 |
