Activity in Technology and Support
Cisco AIR CTVM K9 compatibility
Hello,could u please advise me as I have an AIR-CTVM-K9 that is like 5520 series and 2500 GUI not 9800 functionality..the case is i found C9115AXE-E connected to this wlc? And i was thinking how could it be possible? As Cisco didn’t mention that on d...
2960X image upgrade isse
greetings everyonethis is about an issue i am facing with my Cisco 2960x switches. i did a firmware upgrade from 152-7.E10 to 152-7.E11 image which currently is the recommended one.Unfortunately for some strange reason, after reboot the switch goes i...
Port 49 (mainport)goes Down ist the cause a loop? How do you interpret
HelloI have a Problem with one of my CBS220 switches. I have a non redundant topology. One of my Links GE49 goes down but some times for 1-4min. Can the problem be because of al loop on GE3?How do you interpret it? Where you would start to searchLog...
CBS220 switch configuration for Crestron NVX and Dante
Hello,I am trying to configure a CBS220 switch, specifically CBS220-24FP-4G.I need to apply the settings like specified here for a SG350 switch:https://service.shure.com/s/article/configuring-sg350-switch-for-shure-devices-and-dante?language=en_US&re...
Azure Packet Fragmentation
Hi all,We deployed ISE in Azure back in March (version 3.3.0.430) with the following setup:- 4 x ISE servers (PAN/PSNs)- ExpressRoute from on-premise to Azure- Meraki APsWe noticed we have hundreds of clients stopped responding errors every day and w...
Cisco ISE Profiling limitations
Hello everyone! Thought I would post here cause I have not been able to find an answer to this question anywhere. We are using a product called Medigate (now called Claroty XDome) to profile endpoints and IoT and are piping that information to ISE fo...
Prime 3.10.4 heatmaps not working correctly
HiWe are in the middle of migrating from an old 5520wlc to a 9800. Only a few sites have been migrated so far but we have spotted an issue in prime heatmaps. It seems a random number of AP's will show any kind of coverage on the map while others sh...
Triggering reprofiling with lower CF value
Hi,Further to my previous posts around profiling, I've now stumbled on another issue and wondered if the community has any ideas or can point to the documentation source that sheds light.Say I have a profiling policy with a rule that matches an arbit...
NSO not using commit-confirmed to configure a juniper via netconf NED
Cisco NSO use netconf NED to manage some juniper routers."show devices device xxx capability" from NSO returns below line, indicating the router is a commit-confirmed capable router."capability urn:ietf:params:xml:ns:netconf:capability:confirmed-comm...
ASA Firewall Config Issue with SSH
Hey there.Im trying to setup a management VLAN on my Switch downstairs through my ASA thats on my same network but im having the address on another network so its routed through the ASA to harden up SSH to my address only.Some rough config isManageme...
CME support for 2N VoiceBlue GSM gateway
hello everyone i have a problemI have my router isr series 4300 in which I configured my telephony to that I added a passerele gsm (2N voice blue)My problem is the following outgoing calls from my cisco to my operator pass. but incoming calls do not ...
doubt with fex active-active configuration
Hi, i have a pair of nexus 5548 with a pair of nexus 2232 configured in active-active mode (each n2k are connected to each n5k with 2 interfaces port-channel)so my question is that, the interface configuration of fex interfaces are not synced? so if...
Network phone problem in CUCM system
Hello Cisco Community, I’m facing an issue in our Cisco Unified Communications Manager (CUCM) deployment and I need your support. We have one specific extension that cannot receive any external calls (from PSTN/mobile), while all other extensions in ...
VPS Wirguard CGNAT
Hello I have a homeserver which is behind a CGNAT. Therefore, I use a VPS with public IP which is connected to my virtual opnsense via WireGuard to avoid this. This works perfectly, and I can route the traffic from the VPS directly to my VMs. But I h...
Always On APIC Down?
I cant seem to connect to sandboxapicdc.com. Trying to POST aaaLogin.json as well, timing out.
| User | Helpful Count |
|---|---|
| 181 | |
| 111 | |
| 99 | |
| 81 | |
| 78 |
