Activity in Technology and Support
Looking for German language pack (de_DE) for CUE 8.6.6
Hello everyone,I am running Cisco Unity Express 8.6.6 on an ISM 300 module in a Cisco 2911 router. I would like to use German voicemail and auto-attendant system prompts.I cannot find the German language package online, and I am unable to download it...
UCS C240 UEFI boot option not detected
UCS won't boot. Tried booting using USB Drive, vKVM and finally attached an external CD-ROM. Attached are some of the error messages. Most informational message is when I tried installing CML from a DVD-ROM Drive.
Catalyst 9300 port Audit
Hi All,We have Catalyst 9300 stack switches and have been asked to conduct an audit to see which ports have actually been used in the last 3 months.Which CLI command would you suggest to get some accurate stats ?I have tried show interface link, show...
Request to add test data (devices, sites) to Catalyst Center Always-On
Hi Sandbox team,I'm using the Always-On Catalyst Center sandbox at sandboxdnac2.cisco.com to learn and test the Intent API (via Postman) with the standard devnetuser credentials.Authentication and API connectivity are working correctly — I can genera...
Cisco ISE cni-podman4 interface down
receive this alarm from Monitor Platform for ISE Interface:As part of the analysis, I compared the behavior with the second Cisco ISE node, atollon (172.16.20.130). This node also has a cni-podman4 interface; however, it is in an UP/RUNNING state an...
Resolved! Server load balancing onto itself
hiI have a customer with 4710 that load balances inbound traffic onto 2 servers. this worksThere is also a requirement for the servers that are load balnced to [what seems to me ] to load balance onto themselves and for other server on the same vlan ...
Using EEM to automate a pre-change network check
I'm looking at ways to make routine network changes a little safer by automating some of the checks that are normally done manually.For example, before making a change, I'd like an EEM policy to verify a few conditions such as interface status, reach...
EEM applet not triggering when interface state changes
I'm testing an EEM applet on an IOS-XE switch and I'm having trouble getting it to trigger when an interface changes state.The basic event I'm testing is an interface state change, and the applet should simply write a syslog message when the event oc...
Meraki MX Platform: Missing API Endpoint for Interface Status?
I’m trying to find a way to view the interface status of my MX75 devices in bulk, but I’m having trouble locating an API call that supports this for the MX platform. Is there a Meraki Dashboard API endpoint that provides this information? I can see w...
3802E 4-way handshake M3/M4 timeout / Reboot AP fixes it temporarily
I have a specific 3802E that will stop allowing users to authenticate after a peroid of time and a reboot of the AP fixes it temporarily. The AP is running 17.18.4.201 and connected to a 9800-L-F running the same code: Cisco IOS XE Software, Version ...
Unable to establish communication with route-based IPsec
For our IPsec connection, our site uses policy-based IPsec, while the remote site uses route-based IPsec.When I changed our site from policy-based to route-based, the router’s tunnel interface went up and the connection was encrypted, but the count o...
meraki.com now lands on cisco.com
I've been typing URLs in my browser for 25 years. I've been typing meraki.com in my browser for over 15 and have always landed on the Meraki page where I can signin to account.meraki.com. I rarely create bookmarks. DAE do this?Now it lands on the cis...
C1300 Issue with HA Fortigate
Hi Everyone,We have an issue with our C1300 (4G no stackable) switches. The architecture is quite simple : 2 Firewalls both connected to 1 C1300 switch with : 1 Port channel for client VLANs and 1 port for the ISP VLAN. When we are on firewall 1 - sw...
A new Beta MV Cameras firmware is now available
A new Beta MV Cameras firmware version is available. Firmware MV 8.0 was released on 2026-09-11 and has been in this firmware category since 2026-09-12 UTC.
OSX clients CW9172I disassociations
Having an issue with new CW9172I and OSX clients dissociating for no apparent reason. Users report they lose network connectivity, no ping, no arp but they have IP addresses. At the time the issue is reported we see a ton of 802.11 disassociations i...
| User | Helpful Count |
|---|---|
| 143 | |
| 75 | |
| 68 | |
| 53 | |
| 50 |
