Activity in Technology and Support
C1200 802.1x Missing Settings
I have a C1200-24P-4G switch. For some reason even though i have enabled advanced view on the GUI, I cannot see all the 802.1x settings that the admin guide refers to. For example, the options for MAB is missing. When i go to port authentication and ...
Resolved! A Quick Question - OSPF
An OSPF router has 3 directly connected networks; 172.16.0.0/16, 172.16.1.0/16 and 172.16.2.0/16 Which OSPF network command would advertise only the 172.16.1.0 network to neighbors? A. rtr(config-router)# network 172.16.1.0 0.0.255.255 area 0 ...
Nexus Dashboard on Proxmox
Anyone know if it’s possible to deploy the Nexus Dashboard software on proxmox? I tried for a while using their qcow2 and couldn’t quite get it to boot.As everyone moves away from VMware Cisco will need to address this.Thanks all
Room Kit EQ Serial Port Control Issues
I have two room kit EQ units with a USB to serial port adapter. This is connected to a Crestron controller via RS232. I am not getting RX response from the codec. The user LOGIN REQUIRED has been tested with ON/OFF. The baud rate and settings have be...
CP-8945-K9 upgrading problem
Hey people,im trying to upgrade my cisco 8945 to SIPin cucm i change the device load to whatever the sip version is in device defaults, I checked the tftp server and it does have the sip software, but after i press apply it just gets stuck on the upg...
"Select License Settings" shows "Error ocurred"
In cisco NOOAMP portal showing error The requested page cannot be displayed. Contact the System Administrator if the problem persists. Licence not getting registered for few servers.
BGP routing
Hello Experts, Hello Team,Currently, we have two cloud environments (AWS and GCP) connected to our COLO endpoint devices through two transit hubs, with ECMP enabled across the paths.Existing DesignThe network is presently operating in an Active/Activ...
CSCwp21394 - wired nads failing CTS with error
Hi Also upgraded to latest ISE 3.5.0 patch 1. Switchports started failing with Could not parse the cts-pac-opaque attribute also cts data empty show cts environment-dataCTS Environment Data====================Current state = STARTLast status = Failed...
Cisco 2802i AUX Port as LAN Port
Following the instruction from the link below, I converted the AUX port of one of our Cisco 2802i AP's to a LAN port. My hope was to feed a switch from it so I could provide network access to three devices. So far, I can not gain network access. Has ...
Online APIC API reference site doesn't work anymore
https://developer.cisco.com/site/apic-mim-ref-api/It returns 404 now
Not a valid UI extensions configuration#
Help with the following Not able to read xml -Not a valid UI extensions configuration# <Extensions> <Extension> <Name>Dual Camera Control</Name> <Version>1.0</Version> <Panel> <Type>Home</Type> <Icon>Camera</Icon> <Color>Blue</Color> <Name>Dual Camer...
upgrade CUCM 12.5 to 15
HiCurrently I have a 2 node CUCM 12.5 cluster of BE6H-M5-K9 running on ESXi 7I already upgrade ESXI to 8.0 and plan to upgrade CUCM to version 15- Current CUCM version: 12.5.1.10000-22e- Target CUCM version: 15I would like to upgrade the 2 node and ...
C9300 IOS-XE 17.12.XX packet loss and CLI lags
Dear allWe are currently running 7x C9300-48P all with IOS-XE 17.12.XX.We are experiencing a strange issue where on 5x of the devices we get high latency when pinging the virtual switch interface that is used for CLI access. But it is only happening ...
just want to ask
hi i a little bit confuse how to hide the ssid for this topology
BPDU Guard
Just a simple question why it's recommended to use both Portfast and BPDU Guard together apart from the very fact that both should be used in access switches ports connecting to end users?? Like BPDU Guard will still work if I don't have portfast con...
| User | Helpful Count |
|---|---|
| 75 | |
| 55 | |
| 43 | |
| 40 | |
| 35 |
