Activity in Technology and Support
Resolved! Best Practice for Swapping EOL Leaf model with New Leaf Model
Hello all,I have some older Leaf Models (N9K-C93180YC-EX) that are End-of-Life (EOL) that we will be replacing in the next year or two, and I wanted to start planning on what procedure I will use to swap these out with the newer Leaf model (N9K-C9318...
AI-Enhanced RRM question
deploying AI-Enhanced RRM for a single site which has same RF-TAG as rest of the sites, when configuring CatC pushed this configuration, without getting into exact RF parameter details. wireless profile multi-bssid AI-RRM-PROFILE-BASICdescription AI-...
Add Schneider APC Smart-UPS to Cisco ISE for TACACS+
IntroductionThis document shows how to add a new UPS device to Cisco ISE as a Network Access Device (NAD). It also outlines the configuration required on Schneider UPS devices to support the TACACS+ protocol and the process for defining Cisco ISE Pol...
Cisco CML Network Interface Config
Hello,As soon as I configure third interface in Cisco CML [ens34], I am losing config of ens33:
Netflow doesn't work on Catalyst 9300 switch
Hi, we have configured netflow on Catalyst 9300 switch, but seems it does not send traffics to Solarwinds. We have configured NTA for this switch. But solarwinds never receive any netflow traffics. Below is the netflow config on C9300. Can someone pl...
Cisco Catalyst Center Global Manager
In this webinar, you will lean how Catalyst Center Global Manager offers a unified dashboard to manage large-scale and global deployments. It delivers comprehensive visibility into network health across branches, covering campus, policy, and WAN envi...
Optional IPv4 Static route in Service VPN
I am using Manager version 20.15.4.4 and I am working on migrating the cEdges from device templates to configuration groups, however I am facing an "issue". while feature templates has a check box in the IPv4 Route so it is not a mandatory value per ...
FTD Remote Access VPN SAML w/ 2nd connection using local certificates
Currently have an FTD setup and managed by an FMC with a publicly signed certificate assigned and in use for remote access users with a SAML integration. That is working without any issues. I now wanted to add a 2nd connection method for some mobil...
ASA5545X still sending logs after ACE command LOG DISABLE
Good day team,We have ASA5545X with several S2S iPsec policy based.I noticed that after creating 2 ACLs on OUTSIDE and CP I am still see logs that certain IP is trying ti establish tunnel...I have blocked this IP in regular ASCL on OUTSIDE interface ...
FTD 7.6.4 – RPF neighbor not updated after PIM neighbor loss
Hello,We are experiencing a multicast RPF convergence issue with Cisco FTD 7.6.4 connected to a Cisco ACI fabric.Topology:Two FTD firewalls configured in Active/Standby HA (FTD A is active).Both firewalls are connected to the ACI fabric through port-...
Locked out of CLI in ISE
Team, We have been locked out of our ISE system suspecting CSCvs87754. We need to unlock this as the password we have used for GUI and for CLI is not working. Trying to do the boot method, but the since it is hosted on a VMware ESXI, if we take a sna...
dot1x intermittent
I use fortinac and sometime i got complain from user that they can't access to the network, then i can see in the event viewer there are log And from the switch (Cat 9200L) i got this error Oct 8 10:37:18: %DOT1X-5-FAIL: Switch 1 R0/0: sessmgrd: Au...
Does ISE work/integrate with an AWS Managed Active Directory
Will ISE work/integrate with an AWS Managed Active Directory? I could not find any documentation regarding this .
UserPrincipalName not showing in ISE Log for certain user
I have an unusual issue for certain users when they are using dot1x authentication using TEAP , most of the users are working fine only certain users are not showing UserPrincipalName in their ISE log and eventually they are not matching the userAuth...
CISCO NAM installation by iso generated by System Center
I generated an ISO by System Center, and I want to install by ISO the CISCO NAM and doesn´t work and I don´t know what the problem is. CISCO NAM appears in the control panel and the services.msi but it is disabled and doesn´t work. I need your help p...
| User | Helpful Count |
|---|---|
| 90 | |
| 44 | |
| 43 | |
| 43 | |
| 40 |
