Activity in Technology and Support
Getting error while Add Pod in ACI sandbox
Hi I am trying to add pod in devnet sandbox lab getting bekow error.Can any one help on this or any clarify is this issue on sandbox only?Validation failed: Infra vlan 4 is used by Domain uni/l3dom-HRN_IPNL3Out_RoutedDomain and in AEP uni/infra/atten...
ASA5545-X
Hi all,I'm a student doing home-lab practice with an ASA 5500-X / FirePOWER setup. Cisco has since removed these files from the download portal, so I can't verify them against the official checksum anymore.Could someone who downloaded these directly ...
CUCM and UCCX certificates update .
Hi, I will need to update tomcat and tomcat-trust certs in cucm and uccx . Can you please tell me if i am correct or wrong: I see CUCM has tomcat cert A and the same certificate as tomcat-trust, I aslo see this cert is installed as tomcat trust in UC...
Ceiling Mic Pro mute macro
Hi, Currently have an eq codec with 2 ceiling mic pros connected via ethernet. I want to see how to create a macro to just mute and unmute both ceiling mics together so other inputs can go to the farend without being muted. I tried using co-pilot t...
Looking for German language pack (de_DE) for CUE 8.6.6
Hello everyone,I am running Cisco Unity Express 8.6.6 on an ISM 300 module in a Cisco 2911 router. I would like to use German voicemail and auto-attendant system prompts.I cannot find the German language package online, and I am unable to download it...
Resolved! Meraki Combined template question
I have a bunch of wireless network managed via template. now we are adding Meraki switches, trying to figure out what the best way to go about it, in order to get best network wide visibility for both wired and wireless. The way I am thinking is 1. ...
Tradução para o Português - Versão 9.0
Olá!Não estou conseguindo atualizar para o idioma em Português o Cisco Packet Tracer versão 9.0
3802E 4-way handshake M3/M4 timeout / Reboot AP fixes it temporarily
I have a specific 3802E that will stop allowing users to authenticate after a peroid of time and a reboot of the AP fixes it temporarily. The AP is running 17.18.4.201 and connected to a 9800-L-F running the same code: Cisco IOS XE Software, Version ...
Catalyst 9300 port Audit
Hi All,We have Catalyst 9300 stack switches and have been asked to conduct an audit to see which ports have actually been used in the last 3 months.Which CLI command would you suggest to get some accurate stats ?I have tried show interface link, show...
Resolved! C9200-24P cleaning flash
We have stack with two C9200-24P switches. Flash of first switch displays 1956839424 bytes total (845697024 bytes free) Flash of second switch: 1957167104 bytes total (1358430208 bytes free) I compare content of two flashes - it`s identical (+/- se...
UCS C240 UEFI boot option not detected
UCS won't boot. Tried booting using USB Drive, vKVM and finally attached an external CD-ROM. Attached are some of the error messages. Most informational message is when I tried installing CML from a DVD-ROM Drive.
C1300 Issue with HA Fortigate
Hi Everyone,We have an issue with our C1300 (4G no stackable) switches. The architecture is quite simple : 2 Firewalls both connected to 1 C1300 switch with : 1 Port channel for client VLANs and 1 port for the ISP VLAN. When we are on firewall 1 - sw...
Request to add test data (devices, sites) to Catalyst Center Always-On
Hi Sandbox team,I'm using the Always-On Catalyst Center sandbox at sandboxdnac2.cisco.com to learn and test the Intent API (via Postman) with the standard devnetuser credentials.Authentication and API connectivity are working correctly — I can genera...
Cisco ISE cni-podman4 interface down
receive this alarm from Monitor Platform for ISE Interface:As part of the analysis, I compared the behavior with the second Cisco ISE node, atollon (172.16.20.130). This node also has a cni-podman4 interface; however, it is in an UP/RUNNING state an...
Using EEM to automate a pre-change network check
I'm looking at ways to make routine network changes a little safer by automating some of the checks that are normally done manually.For example, before making a change, I'd like an EEM policy to verify a few conditions such as interface status, reach...
| User | Helpful Count |
|---|---|
| 143 | |
| 75 | |
| 67 | |
| 53 | |
| 51 |
