Activity in Technology and Support
Unable to upgrade from 17.12.4 to 17.12.5 as 'Device is up to date'?
I have a requirement to upgrade a 9300 FIAB switch from 17.12.4 to 17.12.5 using DNAC SWIM process. In the image repository at site level where the 9300 is located I have marked the 17.12.5 image as golden. When I try to start the upgrade process or ...
How to pull back network device site assigment in Catalyst center
I am using use /api/v1/network-device/ to get a list of all the devices on our platform and https://{}/dna/intent/api/v2/site/ to get all the sitesAnd this takes just 5 or 6 calls to get all 800 sites and 4,000 devices. as there is the max 500 per b...
Resolved! FTD to remote FMC register problem
i am trying to register my FTD to my remote FMC by this guide with manual methodhttps://www.cisco.com/c/en/us/td/docs/security/firepower/quick_start/fp2100/firepower-2100-gsg/ftd-fmc-remote.html#task_imq_yw3_b3bbut when i am adding my FTD to FMC i go...
Anyconnect FTD HA design
I have two FTDs set up in HA mode. I want to configure them solely for remote VPN access. I understand that I’ll need an external virtual IP (VIP) for client to reach it externally. However, for internal communication such as the FTD needing to reach...
Complex BYOD guest access with Entra ID Security Groups - Not working
Hello ISEberg,My team is currently working with a customer to deploy a complex BYOD wireless guest access SSID at 100 sites using Entra ID as the IDP. The network technology in use is Meraki MR access points using Cisco ISE on the backend for authent...
CSCug17169 - System password-encryption changes radius password
Has anyone been hitting this bug lately? In particularly when running 17.x.x code. We are encountering an intermittent issue when upgrading code on our 9800 series WLCs, upon boot with new code all AAA/RADIUS authentication is broken. Only PSK WLANs ...
MIC (Manufacturer Installed Certificate) better than MAB auth
I have noticed that the security camera vendor, Axis, ships cameras with 802.1X EAP-TLS enabled and the camera cert is signed by the Axis Issuing CA. The expiration date is the year 10,000 (LOL). You notice the constant RADIUS Live Log errors in ISE ...
Which One Becomes the DP and Blocking Port in This Example?
Folks, I am having a hard time trying to figure out why the G0/2 interface on CD1 switch becomes a blocking port, and the F0/21 becomes the DP. Thus making the F0/21the the blocking port on Acc4 switch. In this example, Acc3 is the root bridge, so al...
Client able to connect due to invalid PMKID
Hello Everyone, I'm facing client disconnection , it tries to connect to the AP and the user is steady and not moving. Captured RA traces and found out the it is happening due to PMKID is sent during authentication.Client sending authentication reque...
Asa site to site vpn between 9.12 and 9.17 failover wan link
I have two wan link first (outside) it's fiber second (outside2) V-Sat the vpn working fine to other side vpn on two interface but the issue the vpns down 4 or 5 time on a day and phone register again every time when I see the monitor vpn active IPse...
PKI FlexConnect Authentication
Hi, I am looking for a guide on how to get certificate working with Cisco C1111-4P (code 17.12.5a) I am trying to get ECDSA certificates working to authenticate over the FlexVPN instead of PSK I think my first question is, is it supported and what si...
ISE - WIFI Profiling Issue
HI trying to do profiling using MAB over WIFI, i had created initial non-profile auth policy that has ACL from WLC (5508) that allows only DHCP, DNS and IP to ISE PSN, device are hitting this auth profile but keep in unknown state if i hange auth pro...
2960X image upgrade isse
greetings everyonethis is about an issue i am facing with my Cisco 2960x switches. i did a firmware upgrade from 152-7.E10 to 152-7.E11 image which currently is the recommended one.Unfortunately for some strange reason, after reboot the switch goes i...
Resolved! Need Switch Stacking Help
HelloWe recently purchased 4 Cisco Catalyst 9300x 48x UPOE+ switches to use in a switch stack configuration. I have made sure that the Stack Wise cables are all connected properly but when the switches boot up only 3 switches are found and are in the...
Issue with configuring leaflist node on yangsuites
Hello, When using yangsuites to configure gnmi request with two leaflist nodes, it seems that yangsuites will create two update request for each leaflist rather than passing the two values in one update request. When I tried to run to modify the ...
| User | Helpful Count |
|---|---|
| 103 | |
| 92 | |
| 90 | |
| 77 | |
| 63 |
