We have our setup using WebEx CMR with CUCM and Expressway C&E, and can connect perfectly with our many SX20's, 80's and Jabber in a 1 to 1 call. However, when I add our 5320 MCU to the mix, we cannot get content to pass through from WebEx to the Ci...
Forum Posts
Hi, I'm trying to find out if it's possible to place a call using a non-video handset and have jabber automatically add in the video. I.E> I'm sat at my desk using a Cisco handset which doesn't have a built in camera. I place a call to another user ...
Hi AllFor some reason we have suddenly come into an issue whereby VC Endpoints registered to our CUCM cannot call the MCU.They get to the auto attendant page and we can see the menu and put in the code for a conference, but as soon as we put in the c...
Hello everyone. And thanks in advance for all the help you can provide. I've been trying to solve na issue regarding the use of SIP protocol based calls. I´ve been making calls only using H.323 protocol, there has never existed the need to use SIP pr...
Resolved! Register Webex Room 55 Dual in CUCM v12.0 - Issue StatusFailed: 485 Ambiguous / Device type mismatch
Hello all,I deployed CUCM v12.0.1.1 with room kit device pack and now I have to register a Webex Room 55 Dual with collaboration endpoint 9.5.1 and select Cisco Spark Room 55 product type with SIP protocol for that requirement. But i have an issue w...
Hello All, After scheduling a recurring (around 40 recurrences) meeting via Outlook, TMS prompts an error in the e-mail staing that "The Cisco TMS was unable to schedule the necessary resources for 40 appointments". Suggested action: Reschedule confe...
Hi, I have a Sip trunk configured behind a Meraki MX doing NAT and I have been through a lot a issue since the beginning. I had to apply some Sip header configuration found on internet from another Sip provider resulting incoming call working but nev...
Hi all,finally i understood how to get PMP license consumed when scheduled meetings are involved, my question comes from TMS's Admin guide - section Enabling Active Directory Lookup. The guide specifies:Enable Active Directory lookup to make user inf...
Hi, I'm having a problem with a SX80 codec.I have 6 microphones connected to the codec. I use the HDMI ouput 1 to send audio signal (local and distant) to an AV system. It seems that the SX80 introduces an audio delay. Should i use exclusively analog...
I have been looking all over the communities and the Cisco Main site looking for Room sizes and layouts for Room Kits an other Video units.Project Workplace does not have anything on the new Room Kit series.Is there something out there that is just b...
Hi,We have to integrate the Cisco Room55 dual with Crestron controller for controlling the blinds and lights through Cisco Touch -10. so how it will possible through RS232 or IP??Please suggest.
Resolved! TX9000 series uplink configuration
Hi TP Community Members, I am looking for Cisco document which provides configuration (or hint to what should be configured) on Uplink Network switch port to which TX9000 codec connects to. e.g switchport mode accessswitchport access vlan XXX (this ...
ALCON,Can some advise procedure to completely whipe a Codian back to out of the box factory reset including reset back to default PWD and no IP and delete any old conference data, logs etc. Make it like it came right from CISCO??? Thank you. Chet
Hello everyone, Would anyone know if DX 80 can pair with Touch 10 for normal operation? If so, is there a specific software version the DX80 needs to be on? Thanks in advance.
Resolved! Spark Room 55 not saving some settings
Hello, I have just deployed three Spark Room 55 units registered to CUCM 11.5. They are running software version 9.2.4. They seem to be working largely ok but some settings are not being saved and are lost after a few hours even if the units are not ...
