HelloIn the macro framework, is there a way I can register to the HttpClientResult response after I send an HTTP get request?In putty, affter sending a xcommand HttpClient get, I get this:*r HttpClientGetResult Body: example I would like to get that ...
Forum Posts
My client has 4x SX20's with Touch 10 panels and 1 x SX80 with a Touch 10 panel. When presenting in a call, all of the SX20's have the Layout option in the top right hand corner of the touch panel, but the SX80 does not. Is there a feature or setting...
HiIs the Call Capacity of CMS 1000 M5 the same as M4?In the data sheet, M4 information is written.https://www.cisco.com/c/en/us/products/collateral/conferencing/meeting-server/datasheet-c78-737519.htmlFull HD 48HD 96SD 192Audio 3000CPU Cl...
We have quite a few Polycom devices registered to our expressway as SIP devices. Previously the interworking on the expressway let us use the public IP of the expressway to call the Polycoms in an h323 format by calling publicIP##SIP extension assign...
Hello Folks, We have a codec that can't be factory reset, has a slow flashing power light and a steady alarm light on the front panel.Secondary Ethernet isn't working, and I haven't had access to a com port cable in years...LOL Any ideas where to sta...
Resolved! DX70 registration by MRA
HI, I had a DX70 and I tried to register by MRA, when I reset the network configuration and the page of configuration of service domain, user and password appears, I put my domain, user and password a error messages says: "secure connection failed, ...
Hello,We have CMS Cluster 3.2 with Expressway E as Web proxy and I have some questions need to understand:1- We suffer poor quality video and sharing from external web app user joining via Expressway (BW showed 235KB) although bandwidth is specified ...
All ... I have a new WEBEX KIT remote installed and they installed the bar upside down. The video on the camera is upside down. Is there an auto flip or flip setting on the codec .. running CE9.15.0.13 firmware Any assist is appreciated.
HiI have a CS-KIT-K9 when I turn on the power, it only lights up white on the front and green on the camera for about 3-7 seconds and then turns off, no signal.There is no signal on the screenThe fan only spins for about 5-10 seconds and then turns o...
I am building a new Expressway Core, version X12.7.1. I intend to use Smart Licensing with an On-Prem Satellite Server. After installing the VM, the option for Maintenance > Smart Licensing is not visible. Do I need to supply a release key for the Ex...
Hello there,I did the upgrade follow the TMS upgrade precedure for redundant servers. I did switch manually from active TMS-01 to passive TMS-02 server and it's stack as it. I cannot switch it back to TMS-01 server - it's just not available in the se...
Dear ,I have MRA solution1-Exp-C 8.102-EXP-E 8.10 (one port configuired with nated IP )3-WatchGaurd (configuired with reflection nat)UC traversal zone is active between EXP-C and EXP-E and added CUCM, IMP to EXP-C.we have one internal domain and othe...
Is there a way to set DND option to Mode instead of Timeout? Currently, it only allows up to 1440 minutes which 24hrs. With Mode setting, you can turn it n or off. The reason behind this request was when I am on a Webex meeting from VC endpoint, inco...
Hi, I hope I'm explaining this right but I wondered where the domain gets appended in the SIP string when dialing into a WebEx meeting with a telepresence endpoint. Here's the workflow:- Book meeting in Outlook and add webex meeting- Add telepresence...
HiI have 2 cms 1000 appliance serverI installed CMS version 3.0.2The 2 server are installed on 2 different siteCMS1 on the site 1 and CMS2 on the site 2 (CMS 1 ans CMS2 have databatse, webadmin, webbridge and callbridge)To get the cluster, I installe...
