hidoes anyone have steps on how to configure n5k for native fc to a storage controller and then map that to an interface running fcoe to a fabric interconnect say 6200 ?appreciate any pointers
Forum Posts
I upgraded my UCS from 2.2.3g to 2.2.8i as recommended by Cisco as a requirement before going to 3.2.2d. This upgrade covered the UCS Manager, FIs, IOMs, and our Blade/C-Series servers. However, the 3.2.2d upgrade attempt failed. Adaptor unit Cis...
Hi I have an issue with a simple ucs setup ucs setup: 2 x fabric interconnects connections (same on both) port 1 & 2 - server ports to left / right 2208xp io modules port 3 & 4 - uplink to switch port 5 & 6 - set as appliance ports - connected to...
Resolved! Fabric
Can i connect FI 6332-16UP or 6248UP to direct NAS Storage ?
Resolved! L2 Disjoint Network impact for vlan-1
Hello Guys, In a scenario with two different switching domains and I need to connected a UCS to both of them, normally I would use vlan-manager to trunk only specific vlans to each uplink.... Nevertheless I have the following questions: 1. what h...
While developing workflows in UCSD, one item that I am having issues finding is how to set the priority of a Vlan. Deploying a new Vlan, and allowing it on a trunk are easy enough. However, I need to be able to set the priority to ensure the proper L...
How do I patch the intel cpu security vulnerability? Is this going to be a cisco firmware update or is it via vmware?
Problem description: We are aware of a new publicly disclosed class of vulnerabilities referred to as “speculative execution side-channel attacks” that affect many modern processors and operating systems including Intel, AMD, and ARM. I see new Cis...
Resolved! Power management functionality UCS C
Hello, How do I configure power management on a Cisco UCS C220 M3 alone host and C200 M2 too?I Need that information for configure a fence agent and hardware settins on RHEV Thanks,
Hi, I was attempting to upgrade the CIMC and BIOS firmware on my UCS C240 M4 server. When using the Cisco Host upgrade utility I selected the CIMC and BIOS and hit update. When the update was finished. I hit exit and my server immediately shut off. ...
Trying to install Windows Server 2016 on a C240 M4. The server has 2 Intel SSDs connected to motherboard SATA ports, so disk controller is the Intel C610 Series Chipset/Intel X99 Chipset Platform Controller Hub (PCH). I have managed to configure th...
Hi Everyone, I recently acquired a UCS-E140S-M1 server, and have been testing out various installations. My great hope was to install Windows Server Preview (i.e. WS 2016 17046), however this only seems to work under legacy booting. I'm aware that on...
Hi , I'm building C240 M4 & C460 M4 servers for our project. I have confusion when choose 10Gb card. I have 2 questions: Which 10Gb card should I choose for only 10Gb connection from server to switch?I choose [N2XX-AIPCI01] Intel X520 Dual Port 10Gb ...
Hi Everyone,I have Blade server B200 M2 using the adapter: M81KR (PID: N20-AC0002). My question is:- What is the maximum UCS firmware version that support this adapter ?- I have checked in Release Note 3.1(3a). I don't see this firmware version suppo...
Resolved! install enic/fnic on Centos 7.4
I try to install enic Driver in actual Version on Centos 7,4 (2.3.0.44) I try yum install also as rpm. The result is, that the Driver is found in the correct Directory: /lib/modules/`uname -r`/weak-updates/enic/enic.ko But the Driver don't load an...
