HX node ESXi version downgrade from VMware ESXi, 8.0.3, 24022510 to 8ESXi 8.0 U1 23299997.Can someone share us proper step to revert this change?@Kirk
HX node ESXi version downgrade from VMware ESXi, 8.0.3, 24022510 to 8ESXi 8.0 U1 23299997.Can someone share us proper step to revert this change?@Kirk
Which VMWARE license is to be bought with cisco ucs220 to build a vmware vsan certied server solution Server is Cisco UCSC-C220-M6S UCS C220 M6 Rack w/o CPU, mem, drives, 1U wSFF HDD backplane Each Server has 2x UCS-CPU-I6326 Cisco Intel Xeon Gold...
Hello there,We would like to upgrade our ESXI version from Hyperflex Connect because we understand that it is recommended way to upgrade both hyperflex firmware and VMware ESXI version from Hyperflex connect. But, I have a little confusion about the ...
Hello, team! Doubtful, with version 5.5, if you install it with vcenter 8.01U, the integration is transparent, even without the plugin? VMware local plugin architecture: Support is limited to vSphere versions 6.5, 6.7, and 7.0. For more information, ...
Hello , I have a Hyperflex cluster which consists of three nodes, and we made a physical migration from place to another place , and I stoped the cluster and put the cluster esxi hosts on maintenance mode, and after relocating the cluster and powere...
We using HXDP 3.0 version, and when I check the status of the HX cluster, it shows that the status is normal. However, in the HX cluster service check section, it fails with the message 'Internal service call failed. Please check configuration.' It s...
Hi All, My hyperflex cluster failed with the error "configure Service profile(SP) failed" "Associating Service Profile" during the UCSM configuration in each server but validation was successful. I have 6 nos of hyperflex UCS 240 m5 all-flash nodes a...
Hi,We have existing running Hyperflex cluster with HX version 4.0.2c and vCenter/ESXi hosts 6.7 U3. Hyperflex cluster has DNS suffix that is domain XXXX.com and ESXi hosts name is esx1.XXXX.com, esx2.XXXX.com and so on.Can we change the name of the ...
Hi All,I am unable to do the cisco hyperflex (Contains 4 nodes) upgrade from and keeps on getting below error. I have already checked firmware/software compatibility before upgrade and also ran pre-check script with no errors/warning in output. ...
Anyone knows if is possible and how to do a repurpose of Hyperflex M5 nodes in UCS Managed Mode to use that nodes to install Nutanix cluster with AHV Hypervisor?
one of Hyperflex SCVM disk space is full. we can login ssh. is there any way resolve this problem and free the disk.
Hyperflex Connect received the following alarm. [HXA-NOD-0008]I searched the document for this content, but I didn't get matching results. Can I ask for advice?There is no problem with the current service.
Hi,We have a cluster of Cisco Hyperflex systems and looking to replace two failed HDDs. These failed SAS drives are visible as "Blacklisted". Please advise if any special precaution is required while replacing these HDDs as I have seen some posts com...
We need to temporarily shut down one of the sites of our HXDP 5.0(2e) based stretch cluster (with RF 2+2). The cluster has plenty of compute capacity (all VMs can easily run on one site). I am hoping it is as easy as:Confirm in HX Connect that cluste...
Hi all. Very simple question, I am getting mixed messages about the above? I can't see any where from the GUI or CLI commands to replace the HX Connect self-signed certificate with a customer signed one? Has anyone done it, or knows if it can be don...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-15-2024 11:16 AM | ||
08-15-2024 08:03 AM | ||
08-14-2024 07:32 AM | ||
08-02-2024 03:36 AM | ||
07-23-2024 08:42 AM |