Hi, We have a setup with a pair of fabric interconnects and few UCS 5108 chassisCan I add UCSX 9508 chassis to the same set of fabric interconnect? (after changing it to intersight manage mode)
Forum Posts
Hi We had an alarm on an HDD. The alarm says: "Predicted Failure - Moderate Fault " so we did the RMA and replace that HDD for a new one. Nevertheless, the alarm still appears. Here is the image of the alarm, note that the state says online, the fa...
cannot create virtual disks or RAID partition. Option 'Create virtual drive from unused physical disks' is grayed out.. Please refer attached screenshots
I was digging through the Broadcom support to see if I could find the latest custom ESXi iso and it seems like several vendors showed up but Cisco did not... Any reason for this that anyone knows? And does anyone happen to have the latest ESXi custo...
DIMMs A0 & A1 failed on my B200-M3 blade. I replaced the DIMMs with new ones. However, the 'Faults' tab in UCS Mgr still shows them as inoperable and the 'Effective memory' value on the 'General' tab is still lower than it should be.I see this in the...
We purchased BE6K-M6 and VMW-VSP-STD-1A.I upgraded esxi to 8.0u2 and tried to apply the Vsphere 8 standard license, but an error window appeared asking me to apply the correct license. Is there any way? "Please provide a valid license key" From what...
Hello all,on one of my SNS-3755-K9 Applience can not open vkvm.after clicking on start and accepting "Load KVM Certifivate" i recieve a blank new Page and 3 Errors (see Screen Shots)Please take a look at this Problem as sonn as possible. Reset Facto...
Hello. I am setting up 2 new UCS 6536 Fabric Interconnect in a cluster. Besides connecting the L1/L2 connections directly to each other, do I need to connect any other the interconnect ports to each other as well?Thank you
IOMDCDateIOM 6/1 (A)A10.nov.2023IOM 3/1 (A)B09.jan.2024IOM 4/2 (B)A12.feb.2024IOM 6/2 (B)A21.feb.2024IOM 6/1 (A)A16.apr.2024Hello do you have any ideas about raisons what could cause multiple hardware IOM failure?Hardware is new, firmware are up to d...
Resolved! SSD/HDD health on C220M7
Hello,Does CIMC on C220M7 (standalone) support SSD/HDD health ( with MRAID12G controller and alert if they are not healthy?UCSM has Smart SSD and I don't think UCSM support HDD health.Thanks
One client wants to buy UCS C220 M4 serverand they have described in the procurement materials Intel Xeon E5-2620 v4 processor and DDR4 2400MHz memories.From Intel specifications I found that this processor supports memories up to 2133MHz. So will th...
HI Team,I recently tried upgrading the C240 M4 (UCSM Integration) to 4.2(3g) C. Unfortunately, I have association failed with upgrading SAS Expander and not able to move forward with the upgrade. Any help would be greatly appreciated.I tried Reacknow...
Hi Team,I am building 2 nodes with Windows Operating System where OS has been installed on the blades and servers are reachable over the network. But we could not be able to get the HBA up to make visible in the SAN switches to proceed with Storage c...
Hi Team, We have an issue in our UCS domain where we have some MAC table is getting above the limit and the reason we found is because a VM mac address that is creating multiple entries in the table with different vlans(all vlans tagged to host vnic)...
Hello,Does anyone have a link to a repository or would care to share the BIOS, CMC, and other drivers found in the latest Host Utility updates for the C240 M3 & M4?I have spent hours trying to update this firmware, I have scraped the internet trying ...
