Voice over IP

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Forum Posts

Is there a Cisco solution to relay/translate between RTP sessions? I will have an application which will handle the signalling itself between VoIP end devices but would like to use a professional equipment to connect the medaia streams transported in...

gkracher by Level 1
  • 987 Views
  • 3 replies
  • 0 Helpful votes

Does anybody know what RASCAL stand for? What's the purpose of this, it looks like it provides statistics/monitoring kind of function. Does Cisco have a document describer each of the IPCC service in detail? thanks

HI, I need to configure the Router 3640 that Gateway SIP with 3 ATA 188. Here the versions(1) Router 3640 12.2.27 (GD) Enterprise Plus 1 PTO WAN 2 PTO Fastethernet(3) ATA-188 Ver. 3.0 SIPThe Router will be SIP Gateway the ATA´s.The Router d...

moiseshp by Level 1
  • 328 Views
  • 1 replies
  • 0 Helpful votes

Based on this config, what would be the QoS values assigned to a packet originating from a directly connected IP Phone?class-map match-any VOICE match access-group 170!policy-map VOICE-EDGE class VOICE set ip dscp 46!interface fa0/1 service-policy i...

jacowen by Level 1
  • 388 Views
  • 1 replies
  • 0 Helpful votes

My AS5XXX gateway with 8 E1s were connected to PSTN,once the gateway start pushing traffic we discoveredthat the E1 is deactivated one after the other.Below is the error message I received when I did show logging:00:24:33: %ISDN-6-DISCONNECT: Interfa...

defash by Level 1
  • 465 Views
  • 1 replies
  • 0 Helpful votes

Hello.I would like to define two routes to the same destination-pattern. i did it by entering two routes on the "Routes" section of the CSPS GUI, both of them point to the same destination-pattern, but one of them has the priority of 1 and the other...

b.shoresh by Level 1
  • 330 Views
  • 1 replies
  • 0 Helpful votes

We have an AS5350 and would like to use it for an automated out bound call campaign. Below is a description of the application:1) The phone numbers are stored in a database. 2) Each number on the database is called (possibly simultaneously to utilize...

I have an enterprise network that consists of 6509 (8.22) msfc (12.2)To run voip on the enterprise is it essential to enable qos? Management wants a case why this should be enabled Our utilization on our wan is 5-10 percent. Will qos matter if we hav...

Hello all,We are having some QoS issues qith our VoIP network. We have a FR access with a 1024K CIR.We just notice that is there are no data traffic on the network, the voice quality is very good, BUT as soon as we started to pass normal data traffi...

aretsu by Level 1
  • 297 Views
  • 2 replies
  • 0 Helpful votes

I'm planning to use this at a remote branch office. Just wanted to know if this also provides voicemail services, or do I require another piece of hardware/software? I'm told that the express version can support 100 hrs of voicemail for those remot...

jrchgtrrz by Level 1
  • 591 Views
  • 4 replies
  • 0 Helpful votes

Hello, have anyone changed logo on 79xx using CCME ??I really did it with SIP firmware and using tftp and bmp2logo tool, but now I dont know how to place that logo using gkdefault profile or any XML config. I have tried "url idle" too, but is not wor...

pepebravo by Level 1
  • 365 Views
  • 2 replies
  • 0 Helpful votes

I need to cross connect on a VWIC D&I card from a circuit that requires ESF to one the requires SF. Is that possible? The fractional T1 is on 0/0 and a Mitel on 0/1. Here’s the running config: controller T1 0/0 framing esf linecode b8zs channel-gr...

salleek by Level 1
  • 384 Views
  • 1 replies
  • 0 Helpful votes

Have a 2651xm running as a pstn gw. When debugging isdn q931, it showsCalling Party Number i = 0x0080, '22222222' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '33333333' Plan:Unknown, Type:UnknownAnybo...

sbrobak by Level 1
  • 4598 Views
  • 8 replies
  • 0 Helpful votes
Top Solution Authors