Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
When we copy profile from corporate laptop to non corporate laptop. I am able to connect to wifi using our credential. How can we restrict it.
I have Cisco 1040 AP with new code 15.3.3-JAB. I would like to skip the guest user authentication and display only the web page disclaimer option for Guest.There is a option called web pass through from GUI and its working.How can i add custom page a...
Is this converter supported in the uplink ports and if so, does it require to change all ports to 10GE and not only the convertor ports ? Because, in that case, can't i just use a normal "server" SPF+ port for 10GE uplink ?
Hi Guys, Got a weird situation, I am on a project which is using the Cisco IW3702-4E industrial access points. The AP's are powered by an external 24v DC PSU. So far so good.... We have a total of five AP's daisy chained back to the router. We have...
I've stood up an eval version of a vWLC 8.2.161 on a UCS E-series blade. I'm trying to test/proof of concept vWLC with a guest wired configuration. This works fine on our physical 5508's, but when I go to create an interface or a WLAN on the virtua...
All, I have just had a looming issue highlighted to me about the cipher offered by the WLC for web-auth. Apparently in iOS 11 (due for release in September) support for the weaker SSL and TLS encryption suites are being removed. Notable TLS 1.0 is ...
Hello Dears Somebody know if is possible to use a directional antenna like AIR-ANT2413P2M-N with 2.4 GHz 802.15.4 radio of Cisco Aironet 1552S? in documentation I found reference only to Omni antennas AIR-ANT2450V-N-HZ Best Regards Ivan Zarate
Hi, Trying to get ISE to profile 1832i, but the access-point wont show up with correct platform in cdp, so the switch cant use device-sensor to send to ISE. The AP shows up with this: switch#sh cdp neiCapability Codes: R - Router, T - Trans Bridge, B...
Hi, I have recently installed a Cisco Aironet 1852I access point which is currently connected to a 3650 wireless controller. For some reason, the access point status shows as downloading in on the wireless controller and remains in this state. Pleas...
Sorry for my lack of knowledge. Is there a way to direct/give more bandwidth to a specific AP for a duration of time? Our issue...we have three AP's in the cafe that run two desktop devices for our lunch program. The students laptops, cell phones, mo...
We have a PRODUCTION HA Pair of 5508 controllers (DC) and a single Anchor controller (DMZ.)We raised a change window to upgrade all three devices. When the Anchor was upgraded to 8.2.151.0 and reloaded.The Screens were flaky, not refreshing, coming u...
Looking at the MSE REST API's "Notification Event APIs".The documentation states: The Notification Event APIs allows an application to register for Push Notifications from the MSE.But the it fails to clarify how the "Push Notifications" are sent -- I...
We've recently deployed several MR33 APs. We did some pretty extensive testing beforehand, so we were confident that all we had to do was connect them to a trunk port, and then specify the management VLAN in the settings for each AP. My trouble is th...
I have existing wireless setup which i am trying to understand . As per inventory list in office we should have 2 2504 wireless controller . But i see only one WLC connected on network . When i login to one of the box I see virtual ip configured 1.1....
Hi everybody, I'm a newbie. I have a poller (centreon) in the subnet/VLAN 172.18.96.1/255.255.224.0, i want to supervise my WLC which is the subnet/VLAN 172.18.160.1/255.255.224.0. The WLC subnet contains other switches too. I pass from the first sub...
