Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I've been trying to upgrade a couple phones to 1.4(4). Call service is CME 8.6. The phone authenticates to network (WEP), downloads config files and attempts to register to CME, at that point the wireless link is dropped, "network busy" is shown. Ano...
Hello, We are currently in the process of migrating from WiSM to WiSM-2. We have a Guest SSID Anchored with 4400 WLC. Previously on WiSM, we had QOS profile configured with a limited bandwidth and it was working fine up and down stream. After mig...
hello, I attached to this email architecture to deploy. the rukus radio link is operational, and the AP in 1552 that is connected in this building is saved on my WLC. I change its role to MeshAP RootAP. I enabled ETHERNET BRIGHING. But other AP 1552n...
Hi, we've created a SSID, which is not being broadcasted. Now I would need to enable broadcast of the SSID-so my question is: how will the access points act after enabling it? Will they reboot automatically?? Or do they even need to be rebooted? Than...
Hi AllI'm working on getting internal WebAuth to work on a FlexConnect local switched SSID. From what I've been reading, it's possible but apparently not very straight forward. FlexConnect AP - if the SSID isn't local switch, WebAuth of course works ...
Will enabling CCKM on an SSID currently configured for just 802.1x authentication reset the AP's associated with that SSID in any way?
Hi,Is there a command to power cycle/reset ALL LWAP's on a controller at the same time? I see there is the reset command on the CLI but this is for specific AP's & not all AP's simultaneously.(Cisco Controller) config>ap reset ? <Cisco ...
We are seeing an issue with an ipad connecting to a WLAN configured for EAP-TLS using ISE 1.2, getting disconnected. The ipad will hop top another SSID. It will connect back to the other ssid when selected. Any ideas? I have a debug client for whe...
Hi guys, My company recently bought a new ap 1600 series which is not supported with the version i was using on my controller and i need to upgrade it to the latest version.We've requested for the latest version and our supplier send as two files "St...
I have Cisco 3602 APs, a 5508 controller, and NCS. I would like to view the client count and client traffic on a particular AP in real time. I know I can view the periodic numbers that NCS pulls but I'd like to see them any time I want. Is that possi...
Hello,I'd like to know if we can encounter problem by mixing different AP models on the same floor; As a client will roam between them and see two different APs capabilities, will he achieve fast and seamless roaming? I mean without disruption especi...
Guys, I have a question regarding LAG ports. From Rajan's post here https://supportforums.cisco.com/document/81681/lag-link-aggregation he mentioned the following: When you enable LAG, all ports participate in LAG by default. Therefore, you must conf...
Hello,I recently upgraded WiSM2 controllers to the 7.2 release and have found that quite a few Accounting Start and Stop packets arrive at the RADIUS server without the Framed-IP-Address.. We use it to login the wireless user into SCE so they are not...
I have some 1130AG (autonomous ) AP's that are working fine.But clients connected to one of them recently starts to have extremally poor connection quality.As channel (1) being used is occupied - decided to change to 6 - after that change (and only t...
When I added to AP to the WLC i checked AP Mode Bridge. I recieve the following error message "Please change the 80211a channel and TxPower assignment method from GLOBAL to CUSTOMwireless->Access points->Radios->802.11a/n->Configure" I am able ...
