Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
I have read everywhere that Cisco PI1.2 combines NCS and LMS2.4 , is Cisco PI 1.2 a single hardware on which you can have both NCS and LMS4.2 lisence ??Thank you
Hi ya'll,I have setup'd two 1142 AP's as mesh.The sceneario is like this:MAP ------ RAP---------SW----------RouterI've done all the configuration through my WLC (Flex7500) and the mesh neighborship is up.The problem is not the MAP nor the RAP broadca...
Hi all,I use two wlc 4400 (4.2.x version) with a mobility domain and one ssid, both wlc are connected to a cisco l2 switch infrastructure. On the wlc I use the p2p blocking action 'drop' (http://www.cisco.com/en/US/docs/wireless/controller/5.2/config...
HIWe have two WDS IWireless Domain Services) in our network.One of the WDS went faulty yesterday and we have replaced it today.Everything is working fine but i have a small query .All the access points are showing registered including WDS in other WD...
Hi,I am having an issue where clients are joining the B Radio instead of A/G.I have even disabled 11mbs and below data rates under the B/G/N radio section and set the SSID to A/G Only but clients are still joining the B Radio.Currently running a Virt...
I have an AP1231G access point and I am trying to configure it as a workgroup bridge (i think is what I need). Here is what I have. In one room I have a wireless router and in the other room I have two computers, switch and AP1231. My goal is to make...
HiI having some troubles with Web Authentication in a WLC 5508 version 7.2 to make authentication with the corporative phones, ANDROID GingerBread 2.3.6 model SAMSUNG GT-S7500L. When I try to connect to the VisitorsWirelessLAN in order to authenticat...
I have a question about 802.11n settings. I have the default radio channel set to 11 and the channel width set to below 40 MHz.Is this correct or should the channel width be set to above 40 MHz?I'm finding a large number of receive CRC errors. Should...
Hi All,Hope to you a very happy new year,I have an (AIR-CAP3602i-E-K9) and I tried to join it to WLC 5508 but I'm facing an error,I get this error from the LAP 1310 console as below:Reading cookie from SEEPROMBase Ethernet MAC address: 60:73:5c:ad:cb...
Hi All,Hope to you a very happy new year,I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error,I get this error from the LAP 1310 console as below:Compiled Mon 17-Jul-06 11:45 by alnguyen*Mar 1 00:00:05.289: %LINK...
We have a WLAN that was deleted from one of our controllers a few months ago. Apparantly the vendor came back and must have the same WLAN rebuilt. We are using NCS and have the backups. How can i retrieve just this particular WLAN without restorin...
Can we use a power injector from a 1410 series wireless bridge to replace a failed AIR-PWRINJ-BLR2 for a 1310 series bridge ? I know there is no console port on the BLR1.
How many maximum clients are supported by cisco aironet 1262 AP and also by a 5500 Wireless Controller?
Hi AllHas anyone had any experience with the new AP1600 with external antennas that was released a couple of months ago.The data sheet shows only 3 antenna connectors although it's a dual band radio AP.This suggests the need for dual band antennas.Ca...
Hi AllI've heard on the grapevine that Cisco has an AP that will work in a cluster with one of the APs working as a controller.I haven't heard this at any PVT and can't find any information anywhere.Does anyone have any knowledge of this?RegardsRoger...
