Hi everyone,Happened to view some logs from our core switch like:Jan 2 02:27:44.265: SW1: IP: recv fragment from 10.80.36.33 offset 0 bytesJan 2 02:27:44.265: SW1: IP: recv fragment from 10.80.36.33 offset 1480 bytesJan 2 02:30:01.655: SW1: IP: recv ...
Forum Posts
Resolved! WAPs with EWCs
Hello - I have a wireless environment that has 4 -1600 series aironet waps that need to be replaced. I see the 9100 catalyst series offer EWC on the access points themselves. If I replaced these 4 would I need each of the new access points to have ...
Resolved! AP 2802i from ME to Lightweight
Hi,I need to convert AP type 2802i from Mobility Express back to lightweight.So far have done hard reset, and when it boots it restarts config wizard for ME. How can I remove ME and make it join WLC againt ?thanks for help !
Hi Guys,Currently I am doing a wireless review. Some of the aspects being reviewed are AP tx power and clients connected to the AP on each radio. I am able to get the tx power on each radio by issuing "show advanced 802.11a/b txpower" command. But I ...
Hi everyone,I currently have 3 x model AIR-AP1832I-K9 running CAPWAP with WLC2504, due to WLC2504 failure I have switched 1 AP1832I to Mobility Express Firmware 8-10-185 mode.After I completed the transfer, the AP rebooted continuously and did not bo...
I have several AP's that all connect to a WLC just fine. There are some AP's that have lots of clients though. Most of my APs have 3 to 9 clients which shouldn't be too bad. One of the APs has 23 clients on it, however. How do I configure load balanc...
Hello,I need sometimes to install my wireless ap on different places that require a static ip adress to connect to the web, but I cannot change the IP that is assigned at first manually on 10.128.128.128, The thing I need to change is the "Client IP"...
Hey,I tried to create a new virtual interface on WLC 3051 but when I click apply and then ok the changes won't save and all the filled box get resetThere is no duplicated interfaceDo you know what should I do?Thanks
Hello Good People,When we are browsing WLC C9800 ip via https it is showing not secure. As far i know it needs SSL certificate. I have found some documents in cisco website regarding CSR certificate and Self Sign certificate. In this case, which can ...
Helloi want it is correct that FlexConnect mode does not support centralized authentication only local authentication ? i wait a reply from expert wifi ?Thanks
HelloWhat are the key factors to consider when deciding between local mode and FlexConnect mode in Cisco Wi-Fi deployments?i wait a reply from expert wifi ?thanks
I have a Cisco WLC 5508 connected to a 24 port Poe switch. Switch is trunked to the router. I have an AIR-AP3802I-B-K9 plugged into the switch and the WLC is on the port right next to it. The ap gets an IP of 10.10.10.4 the WLC wireless interface has...
Hey all,I have an all-around Meraki environment including MXs MS switches and MRs. I wanted to know if there's a way for me to block anyone who tries to remove a cable from my access point and use it on his laptop.Currently the AP's port on the switc...
Hi,I am reffering to the section 9 of this article.Can someone, please, explain the traffic flow during L3 roaming using a concentrator? How exactly it works? If I understood correctly, the default gateways for WLANs in such case are on a core switch...
Resolved! Regarding Upgrade IOS of Cisco WLC-9800
Hi,Currently we are running ios 17.6.0 in Cisco WLC9800 and almost 50 APs are connected. There are mixtures of APs like Catalyst 9105, 9115 and AIR2820, AIR1830. We need to upgrade ios. Does 2820 and 1830 support 17.9.4 ios?Is there any option 'pre-d...
