Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Has the 150ax been abandoned? The current firmware is 10.6.2.0 from 2023. The 140/145 have 10.10 from 2024.I find it hard to believe there's been nothing worth patching in two years.
Hi,We have two SSID's, one corporate SSID with 8021x(EAP-TLS) and the second is Guest SSID anchored back to DMZ.This is standard configuration present at around 1000 sites.Company phones are managed by MDM and connect to corporate SSID doing EAP-TLS,...
Resolved! Restrict bandwidth for guest users
Is there any way to restrict the bandwidth usage Guest wireless users in Cisco DNAC. any pointers to configuration example or article will be good. If it is not possible in DNAC, can we achieve this in WLC.
Hello team, I have some weird problem on few access points connected to L3 switch. This is situation: L3 switch is DHCP for few access points connected directly to it. ip dhcp pool VLAN75_WIFI_MGMTnetwork 10.2.75.0 255.255.255.0default-router 10.2.75...
Hi everyone, As the title said, we just purchased 9163E-E and attached them to our WLC 9800 but their operationnal status are still down. For the record, we had to upgrade our WLC to 17.12.5 to avoid any compatibility mismatch. Now the AP have joined...
Hi all,I’m having a consistent issue with wireless event logs, the first 802.1X authentication attempt each morning is missing the client_ip. Simply disconnecting and reconnecting the client fixes it, and all subsequent log entries include the client...
Hi,Following is the requirement Guest Wi-Fi for external users: 1. User must be authenticated with MFA. User can be pre-defined with email/mobile.2. Authentication must NOT be on AD or ISE.3. External captive portal can be used. Separate auth server ...
Hello,I have mistakenly installed CAPWAP image on the WP-WIFI6 WIM module on my IR1821. I am now unable to install the UIW image that contains the WGB capabilities. The archive download-sw loads the image, but refuses to accept it. It prints the foll...
To give context: my organisation currently has a requirement to provide Wi-Fi to unmanaged devices. 802.1x in general is confusing for users, and deploying certs/passports to them is an additional step of confusion and aggravation. I'm thinking of mo...
Hi! We have enabled second 5GHz radio on C9136. Mode client serving. No FRA. We observe that clients connect to second radio, which is good. I'm want to understand... why? Let me elaborate.From previous tests, we found (3800's, 9130's) that no client...
Right now, I am managing 4 access points(3702i), each part of their own network(each network reachable via routing). The networks are physically close to each other(in a rack). I was wondering if it's worth spending on a WLC(like the 2504) or just ma...
Hi,I have C9136I-ROW joined to the 9800 controller os 17.12.5.It is working fine inSlot 0 : 2.4Slot 1 : 5GHzSlot 3 : 6 GHzI can disable/enable all these three but the problem is for slot 2 that is disabled by default and I cannot enable it, I tried t...
Hello !Could you please tell me if anyone tested EoGRE tunnel between 2 C9800 ?The reason behind is that " -The Mobility Tunnel between 2 WLC's transports only the data-plane (client IP packets) and client context needed for inter-controller roaming—...
Hi all Is it possible to integrate an Azure hosted 9800 WLC into Catalyst Center?
Hello Guys, Have anyone done AP grouping in Cisco catalyst 9800 controller. Via using tags and profiles. i have done going through document. but its boarder to understand. Have anyone provide simple understanding it will be helpful. 2 Groups of AP....
