Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hello, I am having strange connection drops once I configure custom RF profile which is set to Channel Width 40Mhz and apply it to ap-group. Its not caused by long distance from access-point. Goal is of this change is of course to increase throughput...
Hello, Hardware : 9800, 9120 EWCSoftware : 16.12.4a for 9800, 17.3.4 for 9120 EWC We performed some AAA changes on our WLCs and we had to reset the AAA config with a "no aaa new-model".At this point there were no AAA config at all visible either thro...
Hi, I have a cisco ap1815i that boots in (BTLDR) mode .I tried to do the reset with the mode botton and power cycle and didn't work .It doesn't support any known command (set , dir flash ,init flash or boot ).I didn't find any record of this in the i...
I'm configuring a new wireless network using 3850 as a controller and 2702I access point. When a client (iphone) attempts to connect to an SSID it fails and the following is logged on the 3850 console: *Jan 13 21:09:25.790: *%APF-4-ADD_TO_BLACKLIST_R...
We have a new IOS-XE 9K WLC. There are several telemetry connections stuck in connecting status. We dont need to troubleshoot since those peer IP's changed we just need to clean them (delete). I tried googling and cannot come up with the set of comma...
Hi, we're running DNA Center and under wireless assurance I see a lot of Authentication Parameter Mismatch errors in our network. Does anyone know exactly what does this mean? Is it bad username/passwords? EAP protocol failure? Looking for some m...
I am in the middle of deploying 1815i APs in a new building and we're encountering a problem I have not seen before. Some of the APs find and connect to our 8540 WLC normally, but sometimes one will come up in Mobility Express mode instead. When th...
Good morning,My clienet has a Wireless Network with AP-1600 and AP-2800, WLC-3504 controller with Firmware 8.5.161He uses an application that advertises itself via MULTICAST, and it doesn't work.Multicast propagation has been enabled on the controlle...
I see the link web: https://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1850-series-access-points/datasheet-c78-734256.html Say that : Ap 1850 series support mesh in the future, but now is not supportIs this information correct and up ...
Do you know the test report througgput of Cisco 9105AXI Wifi6?We need this information to compare with Cisco 1850i Thanks and best regards
Hello Cisco WLAN Experts,today I discovered a problem with Cisco Prime map.One of our maps is not showing the WLAN AP infos correctly anymore.All APs in 2.4GHz-band show up with name N/A and no symbol for the 802.11b-antenna.I tries several Browsers ...
Refurbishing X-ray portables that have Cisco 1262 AP inside, with three cabled antennas mounted right, center and left in unit. Signal is only good on one side of unit. Have this problem with 2 identical units. Have Diversity selected for RX and TX w...
I am researching using open roaming and I found cisco documentation on how to enable open roaming on meraki devices. It all seems straight forward but where I am lost is how do I capture the info of the authorized user? If a user authenticates with ...
Hello All, I have an issue where we had a 3rd party contractor mount and connect a large number of 2802 AP's around a building and patch in 2 cables to each AP so that both ports are connected. Its not a problem as we only patched in a single cable ...
Hi all, I am reading in the Programmability Configuration Guide, in the New and Changed Feature Information section that Guest Shell started to be supported on Cisco IOS XE Everest 16.5.1a, I am running xe 16.3.9 because I am running converged access...
