Hi guys,As part of POC , I started working to setup wireless Hotspot for guest on WLC 5520 code 8.5.161.0 integrated with our DEV ISE2.6 for webpage redirection and authentication & authorization. I followed all the cisco recommended steps and setup...
Forum Posts
Hi , a question in regards of client behavior. In a case where you would need to tweak the channels in the 5Ghz band (let's say broadcast only UNII 1 & 2) , could this negatively influence clients which are still scanning the entire 5Ghz channel rang...
I have multiple Cisco 5508 controllers running 3502i AP's and I am on code 7.6.100. All of my controllers are using the 40Mhz channel width with channel bonding globally. For some reason, I have one of the controllers not allowing me to run 40Mhz ch...
Hi, I have a WLC 8540 in HA running 8.5.140.0 running 3802i AP's running RRM. I have another another vendor wanting to install their own AP's (2 AP's to be exact) in a special area in our environment, essentially we need to co-exist with their AP's....
All,I am getting error as below; %DTLS-3-HANDSHAKE_FAILURE: [PA]openssl_dtls.c:3191 Failed to complete DTLS handshake with peer <AP IP> I have few AP's connected over Sat link and this was all online and all of a sudden AP's went offline and started...
Hi, New weird issue with the 9800-80 and AP9130. I have about 10 APs up on one edge-switch. 3 of these have joined the WLC and are working as expected. However, the last 7 are nowhere to be seen, even though they have the same DHCP-server (with the s...
I have a quick question for the forum members. I am building a network with lots of guest traffic. I would like to have a captive portal layer 3 security with a customized website loaded on the 9800-40 for guest user Authentication. I am searching ...
Hi guys,1. I need your help, I am gonna set SNMP TRAP on WLC Device, so we can see the status of devices on our NMS systemespecially, if there is some change in configuration line, we want to receive an alarm, and we can check what has been changed. ...
Hi,I've got 3x 1562i's all connected to the same SG300-10MPP Switch. All three have AIR-PWRINJ-60RGD2= installed to power them. These are also all joined to a AIR-CT5520-K9 WLC Switch Firmware: 1.4.11.4WLC Firmware: 8.5.120.0 The APs are booting up, ...
This topic is a chance to clarify your questions about the ease with which an end user, that has no network expertise, can connect a WAN router to the network headquarters of their company from any remote location. The session provides a deep-dive in...
Hi guys , We are running cisco 3504 wireless controller with software version 8.5.105.0. and our co-workers using iPhone X told us when we enable fast transition on wireless controller, they will fail to connect internet. and to test this issue, i di...
Console output:------------------------------------------------------------ U-Boot 2012.07 (btldr release 30) (Mar 03 2017 - 19:13:24)This product contains some software licensed under the"GNU General Public License, version 2" provided withABSOLUTEL...
Resolved! WLC9800-L-F Data Ports
Dears, I am about installing WLC 9800-L-F port-channel to 9500 switch but i read in the deployment guide that 10G/1G uplink not support port-channel as below Data port behavior:• The 10G/Multigigabit copper port (or 10G/1G fiber port) will be disable...
Hi everyone.I want to optimize process of deploy access points (about 1000 APs).Can I create preliminary access point sheets (AP_name - S/N - MAC) and dowload to controller before I will connect APs to this controller?It's actual for both AireOS and ...
Hi Team, I have 2 setups that need a code upgrade.Two 3504 in HA systemTwo 5508 in HA system. I have some questions on code upgrade in HA mode:1. As far as I understand you have to perform upgrade only on the primary and the second one will be automa...
