Hi I went thought the following guides to configure the WLAN sponsor portal but when i try to connect to the SSID i cant get an ip address and i notice only when i disable mac filtering then i get an IP but of cause this doesnt forward traffic to IS...
Forum Posts
I currently have a Self-Registration GUEST network configured on ISE for AirOS WLCs. I have timeout configured on the SSID, which requires GUEST user to re-authenticate after the timeout expires. Instead, can I configure the network so that it requir...
Resolved! Set specific SSIDs on specific APs
Hi,I know I can tag APs and select groups of tags I want an SSID to be broadcasted on.However, I would like to do the opposite, i.e. select an AP and then choose what SSIDs I want to be broadcasted on that AP. Is that possible?Best regards,Adam
Hai, I have Cisco 9800 WLC, AP 1815i and 1562i.1815i APs are joined and working fine.But 1562i Aps are not joining to the controller. Kindly share your information to fix this issue. Below is the logs from 1562i AP:[*03/06/2021 10:39:24.3109] CAPWAP ...
Resolved! Catalyst 9800-L interface
Hi expert In Catalyst 9800-L interface, what I know is 2 units of copper or SFP+ port is used to connect to uplink like core switch.How about remaining 4 units of copper port. What is the used of this port?What I understand is we connect AP to switch...
Hi All, I'm trying to get the redirect ACL working on the WLC 9800, which should redirect users on the Guest WiFi to a self-registration portal hosted on Cisco ISE v3. When I use the following ACL, the user signs into the Guest WiFi and automatical...
My organization purchased 2 Cisco 5700 series controllers, and 50 AP's. The Wireless controller was well configured buti still have not yet got the Access point to work with the controller (AIR-CT5760-50-K9). I have even configured the WLC with varyi...
hi I just want to find out is a Quarantine Vlan Id required for ISE guest portal for (ISE NAC)? i dont need it as i run my guest users as flexiconnect to an interface on a firewall on a remote site. what is quarantine really used for?
Resolved! Help understanding ISSU workflow
Hello, I am preparing for upgrades without downtime for Catalyst 9800 series Wireless controllers with the ISSU workflow.I am specifically wondering how the process works on access points. If i understand correctly the WLC will upgrade APs in a stagg...
I've got a strange issue we are seeing. We have Meraki MR56s deployed with UNII-1, UNII-2, UNII-2 extended, and UNII-3 channels enabled for 5 Ghz.Most clients are fine but I've got some Lenovo laptops with horrible performance only on APs on UNII-3 c...
Resolved! Meraki WiFi 7 AP's ?
A Meraki's WiFi 6 customer asked me about the future release of WiFi 7 Ap's.Where may I find available information?Thanks
I did some testing on the Wi-Fi signal last week and found that all 4 of the WAPs were putting out a very weak signal even when standing directly under them. Further investigation found that these WAPs are set to broadcast over channel 11, the defaul...
Resolved! Upgrading ME Access Points
Hi all, I'm having issues upgrading 1852e to ME 8.10.I was able to upgrade from 8.3 to 8.5 with no facing issues, but when i try 8.10 upgrade it says that that "AP is already on ME"This issue is also seen on 2802e on a customer mine.In 2802e it also ...
Hello Everyone,I have started my job as an IT admin for a company and on the 1st day i noticed some network issues.where we have a cisco aironet controller and 8 AP's connected, these are the following issues: Error 1) cannot update NA SERV CA Certif...
Hi All, I'm trying integrated WLC with LDAP Azure. Scheme : Azure --- Forti --- WLC The final result is wireless client can Login and Connected with user on Azure. Currently WLC can ping Azure, Also FortiGate can reach Azure But we trying connect o...
