Hello,vWLC is setting at ESXi and it has a management interface 10.0.10.2/24-vlan10 and a dynamic interface 10.0.20.2/24-vlan20. The ESXi host trunk to a physical switch that has vlan10 with ip address 10.0.10.10/24 and vlan 20 with ip address 10.0.2...
Forum Posts
Resolved! Wireless Bridge between 2 buildings
Hello everybody,we need to connect 2 buildings - 2 networks with a wifi bridge at gigabit speed.The network uses vlan trunks, distance about 30 meters.Can you suggest units?Thank you,
Resolved! 9800WLCs copy config from lab
Hello there We are trying to migrate WLCs 9800s ACS TACACS+ to Cisco ISE. We were successful in migrating in the lab, but we have issues while on the actual production, is there a method to copy the lab configurations to the actual production. in s...
Resolved! Wlan error
Hi all trying to access wlans but getting the attached error all flex-connect is turned off but still can't access it
1852 restart repeatedly,After upgrading the firmware under u-boot, I can enter the prompt and show version, but restart immediately。What should I do?Can I use part2 to boot? ——————————————————————————————————————————————(RNAQ-C7) # bootipq tftpSpeci...
I would like to use IPSK and I undestrood it works like this:-I will configure one only common SSID-user who will connect to IPSK_SSID and use PSK_123 will be connected to VLAN 123-user who will connect to IPSK_SSID and use PSK_456 will be conn...
Hello Everyone, Scenario - External WebAuth server is using port 8443. In webauth parameter map -redirect url used set as https://External_WebAuth:8443/login.html Two WebAuth ACLs (WA-Sec and WA-Int) are created automatically using redirect port 443 ...
Good morning guys I have two WLANs ("POTIGAS - Coletores" and "POTIGAS - Teste interno") that are configured in a 2504 WLC and that are delivering a wrong default gateway to the wireless clients. The dynamic interfaces are respectively on VLANs 40 an...
Hello, Any one using External Webauth with append parameters? In the AIROS if external webauth (Web Authentication on WLAN Controller - Cisco) is used for SSID, the request to external URL is redirected by appending parameters - AP MAC address, Clie...
Hi I have a MR72 and when I plug it into the wired network everything is great. Now i need to to be wireless so when I plug it into a POE injector (no wired network connectivity just using the POE injector for power, just wanting to use wireless) It ...
I have a Health Care Customer about to Implement C9800s in local mode in HA - 9130s:Has there been any feedback or Caveats reported/known with client devices roaming from 9130.ax to 2800.ac/2700.wave1 environment? A little salt and pepper? IMO..I don...
Resolved! Which Public Cert for RADIUS?
As many of you may already know, Google Pixel phones will no longer authenticate with RADIUS using an internal Cert. So I suppose will need to reach out to a vendor and purchase a public Cert i.e. GoDaddy et al. Have any of you had any luck with this...
Hello, I have set up a iPSK SSID on a Catalyst 9800-40 controller and this works fine for now.The MAC address of the device gets checked by ISE and if the WPA2-Key is correct then the device will be assigned the correct VLAN. However, with iOS 14 App...
9800-L-F running 17.3.2a5508 running 8.5.140 AP: AIR-AP2802I-E-K9 Hello, To begin with I'll supply a bit of history: Around a month ago we noticed that the certificate of the currently active controller (5508) had expired and as a result when AP:s re...
I can't seem to figure out how to log a user out of the CP-8811 IP phone. I have look in the settings on the phone and in the Cisco Unified CM Console. Could someone please point me in the right direction please?
