Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi community, Cisco 9800 WLC running 16.12.4a with 9120 and 9130 APsfor the pass weeks I have been getting the following messages on my WLC logs. Dec 27 20:36:09 EST: %SMART_LIC-5-END_POINT_RESET: End Point list resetDec 27 20:34:22 EST: %SMART_LIC-...
Issue: some of AP3802 ping so high.The wlc 2504 version 8.5.161.0. On the wlc web page-wireless-all aps-ap5~8 both display radio1 is down and not support. AP NameTypeinterface power inlineSSID2.4G5GPING gatewayPING InternetOperationAP11832i15Wtestupu...
Hi expert 1) I would like to know, why DSSS consist 22MHz wide? Why not 30, 50MHz and so on?2) Channel 1 consist 2.401–2.423 GHz (2.412 +- 11MHz). Is that mean AP will send data using 2.401, 2.402, 2.403.......2.423 GHz simultaneously?
Hi All, Over the last couple of days, we have this issue that has come up and causing grief - all APs disassociate and reassociate every minute or so. The WLC is on code 8.5.161.0. The redundancy mode on this is a HA setup, and current status is Acti...
Hello Experts, I'm working on a new project in a large factory, the objective at this first moment is basically to copy the current configuration in 5508 and paste it in the new WLC 9800-CL, I'm having problems with wireless interface in the new cont...
Hello Community,I read the configuration guide for v8.10 and wondering about a contradiction within this guide. https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-10/config-guide/b_cg810/ap_connectivity_to_cisco_wlc.html?bookSearch=true#ID83...
Hello, I am struck up with changing the country code using GUI & Cli cmds and Configuring the SSID with WPA security mode on Autonomous AP with (ap3g2-k9w7-tar.153-3.JBB1.tar) I have one CISCO-3700i access point (AIR-CAP3702i-D-K9) I have done conver...
Hi EveryoneQuick question. In my Wireless>Access Points>Lists page on Meraki, it shows that every WAP disconnects regularly from the controller i.e. "No connection" every day sometimes twice a day for 4 mins. It is shown by a red line in the green co...
Hello community,I'm looking for people willing to share their experience regarding these type of logs in a common debug client Cisco Catalyst 9800-CL Wireless Controller:#12020/11/04 16:16:24.386 {wncd_x_R0-0}{1}: [client-orch-sm] [22104]: (note): MA...
Hi Guys,I am encountering an issue in one of my AP3802E. I have a stack switch (SW1 / SW2) and all configurations are correct. I connect my AP3802E to port 1 of SW2, it can detect power through PoE but the status of the port of the SW2 doesn't come u...
HelloI hope everyone's doing well. I have access point cisco AIR-AP1242AG-E-K9 (very old) the problem is that I have machines under Win10 which do not want to connect to Wifi, they can be recover the address from the DHCP but not access to Internet ...
Hello, I have an issue and i will need your support. I need to change the ip address of the aps and the controller of the wifi from one vlan to another.So far, i have done the following, i changed the vlan configuration at the aps switch ports and af...
Hi, Can anyone assist me how to upgrade Mesh AP AIR-AP1562E-B-K9? Currently i am using the below version:AP Running Image : 8.5.151.0Primary Boot Image : 8.5.151.0Backup Boot Image : 8.5.131.0 Thanks.shrijan
Hello Guys, we have an Cisco AP 1852 with Mobility Express on it. We use this one as controller with some AP1600 series attached. Last week we thought, it would be a good Idea to carry out an software update for the 1852 to lift its firmware to 8.10....
Hi community, I am about to deploy roughly 1000 APs of different models (old 1000 series, Aironet, Catalyst, etc., all Cisco) in geo-dispersed braches. Each branch has their own Windows DHCP servers where there would be IP reservation for all access ...
