I'm working on a bid for a customer that wants to be able to track the amount of time their members are in their facility. I recognize for several reasons why attempting to use network logs to do this may be silly, and this is a startup. I know I nee...
Forum Posts
Hello, We are trying to adjust the channel width on the 5GHZ radio for our 1602i Autonomous AP's Currently using the 20mhz channel width on 5GHZ however when we try to change it on the Web GUI it just gives us an error 404 page not found on any brows...
I have to change the NAT address of my HA pair.. Does it make a difference which device is active when we disable SSO, reboot, change NAT IP, reboot and re enable SSO and reboot? I think that's enough reboots.. of a 5508 production pairI was think...
Hi I'm a developer and new to Cisco world.I need to access via REST API and get List of access points (AP) and latched device list. currently we are having CISCO WLC 55081. is there any REST API for this.2. is it possible to get any sample code...
Hi All, I’m looking at some slides from Cisco Live Barcelona (Intro to 9800 Wireless Controller – BRKEWN-2670) and it has a short section on Inter Release Controller Mobility (IRCM) for AireOS and Catalyst 9800. The headline is, “Seamless roaming b/w...
Hi All. Does Cisco have a list of their differnet WLCs and what the failure rates are ? I am unable to find MTBF for 3504 & 5520 WLC's ? I personally know that Cisco WLC's are utterly reliable. I am however looking for something in black & white t...
Hello for everybody. What is best way to register a certain number of these access points located on a remote site on a controller located in the main DC. To paraphrase a little, there is a site where there is no wifi. Completely new access points of...
Hi, I have AIR-AP3802E-D-K9 i am using "Lightweight Access Point" image and connected with my Wireless controller 2500 series). When i enter command (within AP) "Sh Flash" or " sh version" in telnet or ssh it not showing IOS version in the form of ...
Hello,Perhaps this is just the best I can expect from this particular AP, but I was hoping to break 300 Mbps with this AP setup, as I believe according to the charts, I am getting MC9 speeds and should be able to hit this. Setup / Info:vWLC VM runnin...
Hello, We have a WLC 5520 with APs in flexconnect mode (local switching). I'm almost sure it's possible, but could you confirm we can mix 3802E/I AP models with 3702I/E AP models in the same APs group ? Many thanks by advance.
Hi all,I have a somewhat strange issue to present to you all.I created some new SSIDs for my Meraki lab deployment.The SSIDs appear with the correct name when first detected, however, sometime later, after a reboot or sleep, so far only on Win 10 mac...
Resolved! Flexconnect AP stuck in Standalone Mode
Hi all , I have all of my APs configured under flexconnect at the remote site .I have one controller at the main office .There are two redundant MPLS links going from the main office to the remote site . Now the issue is , whenever my MPLS does a fa...
Hi guys,currently we are using a central wlc 5508 and AIR-LAP1142 access points with flex connect.We got a new branch office where we have bought 9120AX access points for. Futhermore, we bought a C9800 WLC.My idea is to setup the new wlc in parallel ...
Hi ISE 2.2 patch 16.Been having issues with Guest portal, because of lock down, the guest portal isn't being used so looking at the issue. 4 * PSN configured for CWA, when I click on the WLAN, the redirect comes up, not secure even though a new certi...
Resolved! Floorplan display issue
Hi folks, was trying to look at the neighbors on the floor plan but when i select the amp type the following pops keeps happening:I am unable to clear / remove the top box (marker display) and despite the neighbors being selected I am not seeing any ...
