Hello,
customer with ASR9k was asking me if it is possible to change policy-map when it is already attached to subinterface, physical interface or so.
Is it required to unattach the policy-map before we can change it?
Best regards,
Josef
Newbie with A9Ks here.
I got A9K with single RSP as of the moment runing 5.1.3
Now plan to install secondary RSP with default 5.2.0.
Will secondary RSP automatically syncs with Master RSP upon insertion?
Same question when upgrading/downgrading, wil...
Hello all
We use ASR9k for PPPoE termination in our network. We have DSLAMs from various vendors but some (especially older models) have very limited buffer size per port. We wish to perform shaping / QoS on the ASR9K on PPPoE basis. So for e.g. sub...
Dear all,
Our network is peering with 5 ISPs, I'm trying to load balance inbound traffic based on link utilization. now we doing it manually.
I found that PfR do this automatically, but it's not supported in IOS XR,
Is there an equivalent feature to...
My question is if i add a Digital Signal Processor SPA SPA-DSP 1 card to the ASR1001X will i be able field three simultaneous conference calls with max 25 person each call. Or will i need multiple Digital Signal Processor SPA SPA-DSP cards ...
We're trying to configure our ASR 9006 as a PTP slave from a Tekron GPS clock. However, the clock sends multicast PTP announcements and we have been unable to configure our ASR to acknowledge them.
The ASR sends an unicast "Request Unicast Transmissi...
HI
In XR we have user-group and task-group - what is the diff in both ?
Also we have various usergroups such as : netadmin, operator,root-system ..what is the diff among them ?
Can you explain with an example ?
If we configure output traffic shaping on an ASR 9000 interface the Service Policy is not installed, however in cco we can find that traffic shaping is supported see the next link:http://www.cisco.com/en/US/docs/routers/asr9000/software/asr9k_r4.2/q...
Dear All
I have issue with ABF for incoming traffic with label. And from my research I found this word "ABF is not supported for incoming labelled/MPLS packets." in this forum. I just want to make sure this is still not support or it work right now....
Hi,
I'm wondering if there is a way to get the output of the "sh mfib vrf xxx route rate" using SNMP.I would like to monitor and graph the rate of each (S,G) over time.
Does someone know if there is an OID to get this info?? This is for ASR9000 usin...
Hi Guys,
I added css-root.cer and I installed Post-SMU in ASR9010. But, after SMU is installed I can't see the temporary root-cer and I only see the old one.
XXXXX#sh sam certificate bri all-------------------- SUMMARY OF CERTIFICATES -------------...
Hello.
According to official guide
http://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k_r5-3/bng/configuration/guide/b-bng-cg53xasr9k/b-bng-cg53xasr9k_chapter_0110.html#task_4450BCD6473F40AE9BFFF1EF41D1E28C
we can merge services(+ ser...
Hi XR people.
Are there any plans to add support for arbitrary extended communities in an extended-community-set?
That would be a seriously awesome feature!
My specific use-case: Inter-AS BGP Flowspec with support for the Traffic-Redirect action.
I...
Hi,
I'd like to know if there any IOS commands that confirm the the A9K-RSP440L-ALIC license is running on ASR9K router.
The license was installed without problems, but how can I prove that the system now is able to working with 440G by slot?
For no...
