Hi, in XR 4.3.2 I used to have : group mygroup router bgp '.*' neighbor '.*' ! ! end-group to match all neighbors (IPv4 + IPv6) but I can't make that work with XR 5.3.1 which seems to check the regexp on "neighbor" very hard: myrtr(con...
Hello,We've bought NCS-57B1-5DSE-SYS with only 100G/400G interfaces. Because our old NCS-5501-SE has few 10G (CWDM and simple Single Mode) interfaces used, we decided to buy some CVR adapters (CVR-QSFP-SFP10G) for that case from quite trustable 3rd p...
Hi all, I run jumbo frame support test for our l2vpn xconnect service on Cisco ASR 9K platfrom, XR OS is kind of old as 3.9.2I setup AC interface under both end router sub-interface. 200, shown as below:testing IOS router 1 int gi0.200---- int gi0...
Hello,I'm quite old ios-xr user. But still i'm not sure if my thinking is correct. Is it true that line default also activates the same configuration for console even if line console is not configured ?For example i'm using this command to ensure th...
Hello I have server-mapping in network segment routing in operator i want tp know if server-mapping need a License to install or not ? I wait a reply from expert segment routing cisco Thanks in advance
Hello,So far we've been using NCS-5501-SE and the upgrade process was quite simple:It was like: install add source harddisk:/ ncs5500-mini-x-7.5.2.iso NCS5500-7.5.2-packages.tarinstall prepareinstall activate synchronousQuite simple and self explanat...
We've recently installed this device at the edge of our network to peer with 3 different providers. This has been working fine up until recently with the following errors. Are we hitting our limit for ipv4 routes? I cant find anything about this m...
Hello, community I see these strange (ungooglable) error logs on ASR-9010: RP/0/RSP1/CPU0:Aug 11 15:30:36.923 : canb-server[149]: %PLATFORM-CANB_SERVER-3-ALARM_INDICATION : Raise alarm from CBC in slot 0/FT1/SP, alarm code CBC_ALRM_SLOT_ID_CHANGED_RU...
Hi i have been trying to configure a diameter Gy Connection to our OCS platform but keep having these error.Appreciate if anyone would help. Here is my Diameter Config according to Cisco Doc. diameter gydiameter peer a.b.c.ddestination host a.b.c.dtr...
Hi there. Using RSP440 / Typhoon LCs / all -TR SKUs (even at the edge where design would call for -SE) we're observing ~20ms latency added for the case where the router is treating traffic entering on a VRF.MPLS-LDP and MP-BGP provides next-hop traff...
Hello everybody,The Cisco device I'm trying to update is the NCS-5501-SE. The ISO I have is the ncs5500-goldenk9-x-7.2.2-REV05.iso. This is what I did before upgrading the GISO version:The actual router's version: version:7.1.2Copy the ISO to my USB...
We have a few NCS540 running different OS versions experiencing SNMP query timeout.If we do snmpwalk, it always timeout at the same spot after the first few lines:SNMPv2-MIB::sysDescr.0 = STRING: Cisco IOS XR Software (NCS540L), Version 7.4.2 Copyri...
BNG version - ASR 9010, IOS XR Version 6.4.2In our setup, subscriber session speeds are set through policy-maps that are referred by PCRF dynamic templates. When the speeds are 1 Gbps or below, they're successfully getting assigned to the pppoe sessi...
Hi Team, We have configured the port mirrorinng on the ASR 9000 rouuter but not able to observed the packets on the destination interface RP/0/RSP0/CPU0:ASR-9000 #show monitor-session statusThu Jan 22 07:33:12.730 ISTMonitor-session DOT-MIRRORDe...
Hello,for an ASR9006 with RSP440-TR module, can be upgraded to 6.8.2? The actual image is 5.3.4. What is the latest version we can upgrade this ASR to?thank you,
