Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
Showing results for 
Search instead for 
Did you mean: 

Community Activity

AireOS 8.10MR8 Escalation Special

Update As of 2-Dec-2022, the Escalation Special has been superseded by the public release. will continue to be TAC supported, but customers should upgrade to when convenient. Both builds contain the follo...

Aaron by Cisco Employee
  • 41 replies
  • 20 Helpful votes

ASA 5545-X How to connect to web interface ?

Hey guyz  I have managed to fix unit now it boots but now I don't know what to do with interfaces ... I have set G0/0 to DHCP but that's about it..I have brigged g0/1 to g0/7 for inside as well but not sure how to now connect with laptop and see GUi ...

Peter82 by Beginner
  • 8 replies
  • 0 Helpful votes

Rv345 LAG setup later lost connection ?

R (Rv345) setup LAG for two R(s) wireless later, they both lost connection ?LAG1  port9, 3 inR0   2.4/ 1G        port9 ,R2   2.4/5.0G      port3=> error "...internet quality "    

aa321123 by Beginner
  • 1 replies
  • 0 Helpful votes


Hi Cisco Community,I've been tasked with managing our network and i'm being told by contractors that our new installation of 70 x AIR-AP1832I-E-K9 AP's needs to be replaced because the units are EOL. I've done some digging and can see that the Last D...

ASA 5545-X No Boot Image Loop

Good morning or afternoon, everyone.I have an ASA 5545-X that is reloading constantly and with a 'no boot image' to load from. I reset it to factory defaults and reloaded/restarted it, that was yesterday morning. I have put it into 0x41 & 0X1 and tri...

Mereinid by Beginner
  • 1 replies
  • 0 Helpful votes

Resolved! Turning off the FirePOWER sfr module safely on 5516-X

Hello, My customer uses ASA 5516-X with FirePOWER ONLY as a VPN gateway (both SSL and IPsec).Since the ASA is not doing any traffic inspection, the FirePOWER module is redundant and I would like to turn it off. The ASA operates in active/standby conf...

janiax by Beginner
  • 14 replies
  • 0 Helpful votes

holiday reactions disappearing

With the most recent release I had the holiday reactions, and then they just suddenly disappeared and I have the standard emoji reactions.  Does anyone know how to get the seasonal reactions?  I can't locate any help for this.

kmmMI74 by Beginner
  • 2 replies
  • 0 Helpful votes

Support for multiple shared lines

https://help.webex.com/en-us/article/8dmbcr/Webex-App-%7C-What's-New#Cisco_Reference.dita_0f101eca-4aa2-4279-a78a-3169a1809a6e Link's Calling tab "Support for multiple shared lines"is it implemented? I have read the description and understand that I ...

Daosd by Beginner
  • 1 replies
  • 0 Helpful votes

WLC9800 L Cannot get DHCP to work on isolated Guest WLAN

I have a new 9800 L configured on the network.  The corporate WLAN is working and we are getting DHCP.  However, on our Guest WLAN I cannot get DHCP to work.  For the Guest WLAN we have vlanxxx with DHCP coming from our firepower on a DMZ interface. ...

TRNHelp by Beginner
  • 2 replies
  • 0 Helpful votes

Removing `ciscouc` Entitlement via Webex API

Hello. I am having an issue with getting Webex Calling to work within the Webex App (all platforms) for users in our Org, that were originally in the Org when it was Spark Calling. Registering a Cisco IP Phone works fine.  In working with TAC, they a...

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: