hello everyone, how can i configure the equivalent of the ap join profile on the C9800 via DNA-Center, so that there is a custom ap join profile configured on the C9800 via DNA-Center?
Forum Posts
Had DNAC for a 3 months now, running in conjunction with Prime.Before we take prime out of the picture, need to get the reports working.One of the main reports I need is Unique Clients and Users Summary, but this can only do 24hrs"Unique Clients and ...
How do you add outdoor APs to DNA Center? It appears that the DNA Center Network Hierarchy was not designed with outdoor APs in mind. Sure, you can add APs in the vicinity of a building, but outdoor APs are not always close to buildings. They can be ...
Hello I am using DNAC 2.2.2.8 and On-Prem Smart Software Manager version 8-202112 I have a lot of Cisco gear already talking to the on-prem CSSM server (e.g. ISE, Prime, Catalyst etc.) - but DNAC is proving to be really hard. For starters, there ...
Are there any examples of RF profiles for use or guides for configuring DNAC for access points in retail stores in shopping malls? Store sizes can range from 5000sq feet with two access points to stores over 20,000 sq. ft with 4 access points.
I am basically looking for an easy way to montior specific paths between two network devices, and have the statistics (RTT, latency, drops, etc) to be displayed on a dashboard. I am trying to do this using switches/routers as the source and destinati...
Hello,We have 4600 FMC with 37 pairs of FTDs 1140s, and 1150s. We also have a DNA cluster. Is there a reason to integrate the FMC into DNA-C? I cannot find much on the subject besides managing profiles and Configs, which the FMC already does, and ...
Hi All, Our DNA version is 2.2.2.5 and it manages many switches and WLC.How I can do network devices config backup through DNA ? Thanks
Hi,For Non-fabric deployment.I've provisioned the C9800-WLC-1, created WLANs. profiles, managed AP locations, and assigned APs to such location Floor...and life is good; all works as expected.Now I've Provisioned C9800-WLC-2, configured WLANs, profil...
Hello,We have over 1000 managed Cisco switches on our estate, we manage them all via Cisco Catalyst Centre. At the moment we are struggling to pin down an efficient and streamlined process of upgrading them all to the latest IOS-XE version. We are cu...
We are having Gen 1 DNAC with IOS as 2.3.3.7 and during the vulnerability scan we got the below VA "Non-Zero Padding Bytes Observed in Ethernet Packets DNAC " with the resolution as " This weakness may be exploited to fingerprint the Ethernet cards ...
Resolved! Is N9K-C93240YC-FX2 managable via DNAC?
We have a couple of N9K-C93240YC-FX2 switches in VPC pairs running NXOS image version is 9.3(7). DNAC is running 2.3.5.5-70026. Are theses switches manageable via DNAC? As I understand from this dociment: https://www.cisco.com/c/en/us/td/docs/dcn/nx...
Hi Team,We have 5520 WLC in DNAC and wanted to migrate to 9800 , can anyone suggest the recommended way.Traditional migration approach i am familiar , not sure how to plan when existing Fabric WLC in DNA
Buenas tardes, Los molesto por lo siguiente, en los sw cat9300 vienen embebido el wlc, cargamos la versión correcta del ios del sw, pero luego de descubrirlo por medio del dnac, procedemos a la carga del soft del wlc... El tema es que tarda demasiado...
Is there a way to have dnac stop showing these banners and messages over and over again?Our installation is now a few month old, and I have been getting the "Start Tour" and the "Begin your journey" and all other kinds of reminders to enable this and...
