Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi guys,Is there anyway to retrieve existing voice messages and convert them into a WAV files on Unity Connection 8.5? I have setup Unity now to forward voice messages to the users email account as WAV files but we have some messages that ar...
Have a SIP Cube at a remote branch office (London).CUCM running 9.1 at Hub location (US)London Phones and London SIP Trunk from CUCM to CUBE are in same device pool/region etc. Remote branch 7965 phone dials outbound (which will use the London CUBE)...
Dear all,I am running call manager ver9.1.I need to enable BLF feature for all the users.For example: The users can see that the other party is on call or busy on the other line. I mean there is an indication on the ip phone that ...
Olá,Temos um cluster com dois CUCM 9.1 com 6 sites remotos.As ligações entre telefones do mesmo site ocorrem perfeitamente. Mas ligações entre sites diferentes não funcionam, aparece a mensagem (banda insuficiente).* Quando insiro a mesma (location) ...
Hi all,I am using CUBE as SIP gateway. When i run "show call active voice brief" command, all the calls have the same call id 1 or 0. So it is hard to track calls at the gateway. Is it normal? Does anybody know the reason of that?
Hi, everyone.I have a Cisco IP Phone 7942 and I would like to control the phone programmatically (NI Labview) using a PC.Kindly need any expert to advise the possibility to do so or there is a ready driver to do so.Thanks.
Hi all,I need to configure a large amount of dial-peers, all identical except for the destination pattern. I seem to remember that there was a fairly new feature (last year or so) that would allow me to have 1 dial-peer referencing a list of destinat...
Hi,Is anyway to delete the "to send this message now press # or hang up, to discard the message press 6" after recording a message in Unity? I have unchecked everything in Unity but this message keeps there (three times after the call is hanged up). ...
Hi,i am working on a cisco 2911 with CME 8.6, i need to put auth code/ Pin code on to there system, i am not sure how to do it, can anybody help?
Dear All,I want to know how to block outgoing calls for one user, user only can do internal extension calls. I have attached the show tech here, please help me to configure the same as I am new to VOIP.Thank You,Abhisar.
Hi,I get the error 'Domain connection could not be validated' when i click OK with the below configuration under Enterprise settings in the QM Admin. It was working fine before. No change in the password, give the same error even with new user ID as ...
Hello Experts,I have a Cisco 2921 router with VWIC3-2MFT-T1/E1 card. On this card we have T1-CAS digital line connected. We have been provided with a set of DID numbers. We have a requirement where, when we dial a DID, the router should provide a dia...
Hi,In getting ready to add an off-site office to a CUCM 8.6 across the street, a 7941G that was built and registered at the home office was taken and connected to the LAN at the new office. The CUCM 8.6 DHCP server is used on the publisher at the ho...
Hi,I want to open firwall ports for traffic between our Cisco CUBE and 1.clients Cisco CallManager Cluster and 2.service provider SBC. What are the ports I need to open on firewall? -Is it sufficient if I open ports TCP/UDP 5060/5061(SIP) and UDP ran...
Hello,There are a lot of litterature / Documentation concerning Fax in a Cisco VoIP Environment. Problem is we can easely get lost regarding all the possible configuration, ie Fax Relay, T38 Fax Relay, Modem Passthrough, Fax Passthrough, combination...
