Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
While waiting for our SIP service to be ordered, I want to get our 9971 phones talking to Call Manager. I have an internal ASA running 8.2.5 code to pass through from the phones to Call Manager. I am not running NAT or PAT on the ASA. From Call Ma...
Dear Experts.... After analyzing my CDR in cucm i found that few (2 or 3) calls are found to be of around 6hrs to outside PSTN through router (FXO port)Its for sure that these calls were not made actually for this much hours.Inter...
I have installated Cisco IP Communicator v8.6.1.0 on Windows 8 64 bit. but it'c can't working properlly. kinldy advice. any Version available for Windows 8 or any other option.Thanks.
Hello guys,Some users are not recording calls but other in the same team do !Computer is behind the ip phone, there are not firewall or antivurus block the comunication. What else can cause this issue?Thanks for help,Gabriel
Hi, I have a problem with Linksys PAP2T ATA:I have call manager express on cisco 2811 (version 7.01) and I configured ephones and ephone-dn as the followings:ephone 2 device-security-mode none mac-address A0BB.6D41.2C01 max-calls-per-button 4 userna...
Hi!I am trying to jump upgrade from current 6.1.5 to 9.1.1 as stated in document "Jump Upgrade Procedure for Cisco Unified Communications ManagerRelease 4.1(3)–7.1(5) to 9.1(2)"I already have virtualized my installation and it successfully works in V...
We are testing some 8941's through a VPN connection. My tester in the remote location has been testing by calling 2 phones in his office. Is this a valid test of a Video Call through a VPN connection? Does call manager hand the acutal call off to ...
Hi, i would like to use Cisco UBE to permit SIP registration from Internet to my internal PBX. I've found many guide on internet and i've tried to implement first a simple registration of SIP client. The problem is that my PBX "challenge" the incomin...
Dear Experts.... After analyzing my CDR in cucm i found that few (2 or 3) calls are found to be of around 6hrs to outside PSTN through router (FXO port)Its for sure that these calls were not made actually for this much hours.Inte...
Hello,Have a setup with a fractional T1 (Voice PRI) dialing into and out of a 2811 running CME.Should we want to upgrade to CCM can i point the PRI on the 2811 to the CCM? Or will i need a different kind of gateway? ThanksJohn
I want to deploy a Wide Area Network IP telephony communication so all my offices and sub offices can use the IP phones technology. What equipment and software do I need to procure? I need 200 IP phones for sure, for all my workers. What softphone wi...
Hi supporters, when I start calling from my Cisco IP phone to a dialog phone, I try to hang out to stop the call but I can't. I was press end call but dialog phone still ring, it's none stop. My Cisco IP phone's firmware is SCCP and my account regist...
Hello, we have a CME and what is needed is to host conferences; Participants from outside will call into a specific number then they will be prompted for a code to join the conference or get it started. Please advise what should be done or needed for...
Hi All UC Experts,Can the VG 2921 work on the BE3000?If it can, all functions or limited functions?
Hi,I not able to add more than two PRI's on my Cisco 3945 Gateway. As you can see in the below attached the configuration file the third controller is partially registered. Also you can see that both the transcoder and conference profiles are shut do...
