Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello,Wondering if anyone else has see a switchport stop forwarding when an ATA is connected and the swtichport voice vlan is set?I am experiencing this with ATA 187's on all of my switches.Thanks,Dan.
Hi,I have 5 Ip Phones (1x 7941, 1x 7912, 3x 7911). Only one 7911 has been registered, but the other devices stucks in registration status. From a "show ip dhcp events" I got these lines:*Aug 18 10:55:40.779: DHCPD: Sending notification of ASSIGNMEN...
Hi All,I would like to know the error message will user get if all the trunks are busy.For example,I have one T1 PRI and all the 23 channels are used up.If a user tries to call pstn line,that means 24th call,what will be the error message that user ...
I have found several documents on T.37 Faxing but none are overly clear and all seem to reference older IOS. Does anyone have a document or configuration reference for configuring T.37 fax on 29XX/39XX ISR running 15.X code?Any help would be appreci...
Hi, I'm trying to purchase a C881-V-K9. I want to run CME on it. It supposedly supports up to 5 IP phones. When ordering this router, under CME-SRST LIcense, I can select FL-CME or FL-SRST. Both are $0.00. However, there's also an IOS Technology Pack...
Does anyone know if C892F-CUBE-K9 supports CME? I can't even locate any specs on this router. Does it have DSPs? The Feature Navigator states that it supports CME (up to 8.6). However, it may need the SL-8XX-UC-K9 license to activate the CME-SRST fea...
Hello Everyone, has anyone had experience of integrating a Frequentis (ICCS) system to callmanager via SIP trunks? I'm especialy interested in the SIP part and what was done to get certain facilities to work such as transfer of calls etc.Many ThanksP...
Hi guys,I have a project where i have 1 cucm (pub&sub) and one voice gateway with 4 E1 lines ,each company should use one of these E1s !I think about MGCP because in the route group ,each one of the e1s could be chosed seperately in a seperate route ...
Following are logs of IP phone, how can i find out date from this ? 10:04:16p 23: Name=SEP24B657444925 Load= SCCP42.9-2-3S Last=Reset-Restart 7:39:00a 23: Name=SEP24B657444925 Load= SCCP42.9-2-3S Last=Reset-Restart 11:47:34p 14: Name=...
Hi there,Can "call forward unregistered" some how be configured on a CME 7.1 for SCCP phones, or is ther some workaround?I know, for SIP it's possible. What I'm trying to achieve is, if a home ofice SCCP phone/DN is not registerd with the HQ, the inc...
Hello,I am having some trouble finding an example of setting up a fxs port with an analog phone. I would like to be able to place a call from the anlog phone that is connected to the fxs port. Everytime I try and configure it I get a busy signal. ...
Hi is there anyone has an experience with netcom adsl router that support sip and configuratin to cucmSent from Cisco Technical Support Android App
Hi,a.)Group 1 --> CM1, CM2,CM3Group 2 --> CM2,CM1,CM3And b)Group 1 --> CM1, CM2,CM3Group 2 --> CM2,CM1,CM3 Group 3 --> CM3,CM1,CM2Group 4 ---> CM2,CM3,CM1ORc.)Group 1 --> CM1, CM2,CM3Group 2 --> CM4,CM5,CM6Which qualify as 1:1 or 1:2 reduancy?IF the ...
Hi,Is it possible to resize my Call Manager cluster to get ride of some extra Vitrual Machines(VM) (This is all running on Cisco UCS)for example (current cluster)Phones = 10,000Using 2500 (larger vDisk),4 GB RAM1x80 Gb1 vNic4 subscribers each with 2,...
Hi All,Anyone know if the below command has a SIP equivalent?telephony-serviceurl idle http://XXX/idle.php idle-timeout 5Trying to get the SIP handsets (9971) to display the same page as the SCCP phones.
