Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,I just had an issue where CEF was pegging the CPU on one of my CUCM servers causing call delays etc. I reset the service and everything is fine, does anybody know what could cause this process to peg at all?Thanks in advance.John
What is the max. BHCA supported by CUCM Cluster & Mega ClusterThanks Sam
HiI'm planning for a CME projectRouter 2921 with CME 9.5Call Processing ISDN30 & SIPNumber of Phones 60 (7906,7945)users are divided in to two separate companies (30+30)as a requirement 30 users on DepartmentA should use ISDN for incoming/outgoing wi...
Hi all,We need to configure remotly the favorites to some endpoints registered in our CUCM (8.6).The problem is that we need to configure some endpoints with IP and the directory number in CUCM is not able to do it. We telepresence systems we use the...
I am getting these events on my CMM Cisco IOS Software, Cat6K-lc Software (wscmm-IPVOICEK9-M), Version 12.4(15)T11. does anyone know what htese events mean? Thanks, AlbertMar 24 16:04:01.658 PDT: (1/1) Framer: 0, Event: CMQ_EVENT_T1_FRMR_INFRM, In-f...
I have a Unity Connection 8.6 HA. Licenses are installed and look fine from where you import however if you use the Tools Task Management and use Check system configuration I get the following error Any ideas
Hello Im running on a Cisco Router 2811IOS version C2800NM-SPSERVICESK9-M, Version 15.1(3)T4i have 1 E1 as QSIG connected to a PBX and another E1 to the PSTN#Show VersionCisco 2811 (revision 53.51) with 507904K/16384K bytes of memory.Processor board ...
When I make a search of anybody on Corporate Directory and select the option key of Dial to an extension number of a member, nothing does. I looked to an option on Enterprise Parameters and Service Parameter Configurations, but there is no configura...
At one of our sites they have a call handler with a simple setup.Inbound calls ring and if no answer they go to VM.I can add a destination DN as a coverage path.But can I make that destination DN be active via a timed schedule?
Hi Akon as you know, we recently configured CUBE (ip2ip) gateway for the new SIP link but caller-id is not working properly. It works for some outbound calls and does not work for some outbound calls. I noticed a pattern when it CLI works and and whe...
I have the 2851 Configured in call manager. The FXS cards are setup as POTS.The CSS and Partitions are correct.Nothing is blocked.I can send and recieve faxes internally with 5 digit dial.But cannot receive anything from the outside. You can hear the...
Greetings! Bear with me as I'm reletively new to the whole Linux app side of things. We upgraded to CuCm 8.5 and Unity connection 8.5 from version 4.0 (which was windows)We've decided it's time to check for security patches / updatesWe are avoiding ...
Hello all,First, a little background:I'm the defacto VoiP SME on my project. I have no formal training, and have been learning as I go, so please talk slowly, and use monosyllabic words.The environment is CUCM 8.5 running on an isolated, but global n...
First time I have played with this device and I am trying to get an ATA187 to register but failing. From debug tftp events it cycles around looking for the 2 addresses. the valid one being 105C5F12F501.Originally and in error I had put the full mac 7...
Dear All,I am running CUCM 5.1.1 on MCS server. And i have installed CUCM 9.1 on UCS sever.I need to import ip phones registered on MCS server to UCS server which is already running on cucm 9.1Kindly can anyone gudie me the procedure to perform this ...
