Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi to allwe have 6941 phones and you already know that they have only one line.Call waiting is not supported by this seriesSo we have creted another one virtual extension and when the first line is busy then the second call going to the second exte...
Hello,We have brought up a couple of 9971 phones and unable to get the company logo to disply. We have loaded the company logo on the 7945’s but unable to do so on the 9971’s. Used 640x480 as per the doc but the image will not display on the phone....
HiDoes anyone have information or knows where to find information about countries that have VOIP restrictions.In india for example it is forbidden to connect A PSTN call with a VOIP call so TEHO, transfer of calls to other voip sites and so on are fo...
Due to bug CSCtu18692 I need to increase the vCPU commitment on a CUCM 8.5 VM. The publisher is pegging CPU every night during DRS and TAC's guidance says it could cause outage and should be addressed.I've read mixed results on adding vCPU resources ...
I insert the DVD in the tray of the server and I restart the server, so it boots from the DVD. The wizard of the installation of CIsco Unified Communication is showed. The question of the Wizard or Initial Configuration are showed, these question are...
Hi I have a CallManager Cluster (ver 6.1) and a voice gateway (Cisco 3945). All my other gateways are running mgcp but this one cant as CUCM 6.1 does not support 3945 using mgcp.Routing to and from a site using a 3945 works 100% using h323. Only p...
I am running CME 7.0 and configured extension mobility. After entering the username and PIN for EM login, the screen hangs dispaying "logging in". Pressing the exit softkeys shows that the user profile has been loaded succesfully. The issue is en...
Hi alli need your opinion regarding the belowUsually with CUCM in cluster mode we use as primary the subscriber to register their the ipphones , publisher is a primary for the tftp and for the other jobsThe above senario is when the cluster is over t...
Hi,I'm running into a strange issue with ATA187s. Calls from PSTN to phone/fax attached to ATA 187 will not connect.The PSTN caller hears ringing all the time even when the call is answered. The phone connected to the ATA hears noises when the call ...
Hoping someone can point me in the right direction with this problem. A user presses his messages button and accesses his voice mail. It says he has one new message which he does and to press "1" to listen to it. When he presses the number 1 on his p...
I use ATA 187 (firmware ATA187.9-03-0) with cucm 8.0.3.20000-2 for fax. the topo belowPSTN---- T1---- GW ---H323(g711 u-law) T38 -----CUCM ----SIP-t38----ATA 187 ------FAXServer ( Brother 2920).I used fax relay with T38 protocol and fax rate set to...
Hello Coleagues please can some help regarding the blackup of CUCM 7 using titan or other software , at the moment i'm using titan but i m geeting every time i'm doing backup .could you assist with guid line how to do the backup
Hi to allWe are going to install meeting place 8.0 application server I have read in this document @MeetingPlace 8 Integration Webex Type 2 Configuration Example@ that you in order to install meeting place you need:Reference to quideThere are two CDs...
Sometimes when im in CCM admin and I look at all the devices they have a (1) next to them. eg. upcjdoe(1). This happens periodically and then just goes away. Anyone have any idea why this happens? Is this a 6.1.5 issue? Ive recently (two months a...
Hi, im my company we have a few configurations like that, a manager have a CFA configured towards his assistant, but some people needs to override that, so there is a Hunt Pilot, having just the manager DN int the line group, well, this is working fi...
