Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear all, Can some help me to reset the passwor for 9971 ip phone i have no power cable for the phone.I was trying to configure with 2911 cme 7.1 with 50 user.lic with CP before configuring this phone i can access admin i tried the password which i...
Would someone be kind enough to assist with the following issue.I have a customer who has bought several E20 Video Phones. The customer has CUCM 6.X and the Documentation states, Although supported on 8.5, If the firmware is down graded to TE2.2.1 t...
Hi All, I need to to make a simple config on CallManager express.I need to make a 4 digits number when dialed be transformed to a PSTN number and routed.How can i do that in a way that is available for every dn on the system.Do i need to create a dia...
Hello all!I've a 2800 series router running CCME 7.1 and i'm trying to get a SPA 502G IP Phone up and running. The phone obtains the correct IP configuration but does not register. I did change from scsp to sip using the menu button of the phone, and...
Hi All,After upgrading Call Manager from 6.x to 7.1.3 our Cisco ATA 186 is not working and when looking at the configuration page for the Cisco ATA 186 it states "Device is not trusted". Can anyone please explain why this is happen.Thank you.
Dear Cisco SupportI am running cisco call manager 4.1 publisher and subscriber.I am trying to add new Cisco IP Phone 7945 but i am getting below error messages.'Cisco Discovery Protocol (CDP): Switch Port: Warning! CDP should only be disabled on th...
I want to make a pin code required when someone dials 9 or is trying to get direct line ...the phone is already with direct line feature but I want authorized users only to log-in and be granted the line otherwise internal calls only and emergency ar...
Hi , I musing CUCM 8.5 , and i want to synchronize with Microsft AD.I have configured LDAP on CUCM with Success " when i Perform a Full Sync Now " I have a result " Update Successful".But the problem , i cant import any user?the CUCM and The AD are ...
New cm 8 install and I'm having issues with the 7945 phones not being able to download files (ringlist, phone config file, etc) from TFTP. I think it is related to ITL and the security by default. My CM is setup with system>server set as IP address...
I have a H323 GW configured with SRST. If it was MGCP , I would just shut down CCM Service so to force the phones and router in SRST and use the however how do you does this with a H323GW- I can not think at the moment so excuse the stupid question. ...
Hi all,I have several remote sites that share the same gateway for outbound PSTN calls and I am looking for a way to translate Calling number of extensions to a 10-digit number (like the main number where the call is originated from) for outbound PST...
I am planning on replacing the voice funtionality of a WS-X4604-GWY with a 2821 with 2x PVDM2-32's. I am not sure how to compare the DSP resource to ensure the 2821 would be sufficient, as no DSPs are listed in the 4604 module with "sh inv". A "sh vo...
Dear all,I have a question about uccx script. I can get session ID from script when accept call but how to get agent's extension form session ID.Please help me to solveThank you very much.
Hello I need to migrate a CUCM 4.0 to 8.5 the number of the update is as follows: MIG-CUCM-USR-A, anyone know the procedure to obtain the license file for version 8.5
I’m running CUCME 15.1(2)T / CME 8.1. I’m trying to create a local speed dial based on the following document: http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmespeed.htmlI have placed 32 entries in the speeddial.xml...
